在QIBA体模研究中比较超高清CT与多探测器CT采用不同扫描模式及包括深度学习重建在内的重建方法对肺部CT值和气道尺寸评估能力
本研究在QIBA推荐的肺密度与气道体模中,直接比较超高清CT(UHR-CT)不同扫描模式与多探测器CT(MDCT)不同重建方法对肺部CT值和气道尺寸的评估能力。结果显示,UHR-CT的扫描模式和重建方法均会显著影响肺部CT值和气道尺寸评估,其影响程度与MDCT重建方法相当。
要点
- UHR-CT的扫描模式(SHR、HR、NR)和重建方法会显著影响肺部CT值和气道尺寸的测量结果。
- 在0.5mm和1.0mm层厚下,SHR和HR模式的气道参数平均差异显著小于NR模式和MDCT。
- UHR-CT各模式与1.0mm层厚MDCT(FBP重建)的肺部CT值平均差异均存在统计学显著差异。
核心结论
- UHR-CT所使用的扫描模式和重建方法会显著影响肺部CT值和气道尺寸的评估,其影响与MDCT所用重建方法类似。
研究设计与样本
- 体模研究,采用QIBA推荐的肺密度和气道体模设计;比较UHR-CT(NR、HR、SHR模式)与MDCT(FBP、混合迭代重建、基于模型的迭代重建、深度学习重建)在0.25mm、0.5mm、1.0mm层厚下的测量表现,以FBP重建的1.0mm层厚MDCT作为参照,采用Tukey's HSD检验进行多重比较。
诊断标准与关键数值
- 在0.5mm和1.0mm层厚下,SHR和HR模式的肺部CT值及所有气道参数的平均差异与NR模式(UHR-CT)及MDCT相比具有统计学显著差异(p < 0.05)。
- UHR-CT各模式(SHR、HR、NR)在所有层厚下的平均差异均与1.0mm层厚MDCT(FBP重建)有统计学显著差异(p < 0.05)。
- SHR和HR模式在0.25mm、0.5mm、1.0mm层厚下的肺部CT值平均差异显著大于1.0mm层厚MDCT(FBP重建)(p < 0.05)。
- SHR和HR模式在0.5mm和1.0mm层厚下测得的内径、内面积和壁厚的平均差异显著小于NR模式(UHR-CT)和MDCT(p < 0.05)。
局限性
- 原文未报告局限性。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
英文原文(摘要)· 点击展开
OBJECTIVE: Ultra-high-resolution CT (UHR-CT), which can be applied normal resolution (NR), high-resolution (HR), and super-high-resolution (SHR) modes, has become available as in conjunction with multi-detector CT (MDCT). Moreover, deep learning reconstruction (DLR) method, as well as filtered back projection (FBP), hybrid-type iterative reconstruction (IR), and model-based IR methods, has been clinically used. The purpose of this study was to directly compare lung CT number and airway dimension evaluation capabilities of UHR-CT using different scan modes with those of MDCT with different reconstruction methods as investigated in a lung density and airway phantom design recommended by QIBA.
MATERIALS AND METHODS: Lung CT number, inner diameter (ID), inner area (IA), and wall thickness (WT) were measured, and mean differences between measured CT number, ID, IA, WT, and standard reference were compared by means of Tukey's HSD test between all UHR-CT data and MDCT reconstructed with FBP as 1.0-mm section thickness.
RESULTS: For each reconstruction method, mean differences in lung CT numbers and all airway parameters on 0.5-mm and 1-mm section thickness CTs obtained with SHR and HR modes showed significant differences with those obtained with the NR mode on UHR-CT and MDCT (p < 0.05). Moreover, the mean differences on all UHR-CTs obtained with SHR, HR, or NR modes were significantly different from those of 1.0-mm section thickness MDCTs reconstructed with FBP (p < 0.05).
CONCLUSION: Scan modes and reconstruction methods used for UHR-CT were found to significantly affect lung CT number and airway dimension evaluations as did reconstruction methods used for MDCT.
KEY POINTS: • Scan and reconstruction methods used for UHR-CT showed significantly higher CT numbers and smaller airway dimension evaluations as did those for MDCT in a QIBA phantom study (p < 0.05). • Mean differences in lung CT number for 0.25-mm, 0.5-mm, and 1.0-mm section thickness CT images obtained with SHR and HR modes were significantly larger than those for CT images at 1.0-mm section thickness obtained with MDCT and reconstructed with FBP (p < 0.05). • Mean differences in inner diameter (ID), inner area (IA), and wall thickness (WT) measured with SHR and HR modes on 0.5- and 1.0-mm section thickness CT images were significantly smaller than those obtained with NR mode on UHR-CT and MDCT (p < 0.05).
引用
- Ohno, Akino, Fujisawa, et al. Comparison of lung CT number and airway dimension evaluation capabilities of ultra-high-resolution CT, using different scan modes and reconstruction methods including deep learning reconstruction, with those of multi-detector CT in a QIBA phantom study. Eur Radiol. 2022. PMID: 35841417. doi:10.1007/s00330-022-08983-1
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。