采用连续多圈反向螺旋扫描扩展术中纵向三维锥形束CT成像
本研究在固定房间机器人CBCT系统上实现多圈反向螺旋扫描,将纵向覆盖范围从17 cm扩展至80 cm(增加370%),扫描耗时100秒;几何模体测量精度达亚毫米和角度级;在羊尸体胸椎T1-T12椎弓根螺钉固定术后评估中识别4处皮质穿破,与术后CT一致,螺钉角度与CT测量平均差异轴向3.3±2.6度、矢状面1.9±1.5度,观察者间ICC均高于0.900。
要点
- 多圈反向螺旋扫描将术中CBCT纵向覆盖从17 cm扩展至80 cm,单次扫描100秒完成。
- 几何模体测量精度达亚毫米(0.2±0.1 mm)和角度级(0.2±0.1度),无失真。
- 羊尸体胸椎螺钉术后评估中识别4处皮质穿破,与术后CT确认一致。
核心结论
- 在临床机器人CBCT系统上,多圈反向螺旋扫描实现纵向扩展视野的术中三维成像可行,可在单幅图像中显示长解剖部位,包括存在金属硬件时。
研究设计与样本
- 在固定房间机器人CBCT成像系统上实现多圈反向螺旋扫描,用简单几何模体检验运动特性和几何精度,并在羊尸体上完成胸椎T1至T12椎弓根螺钉后路固定术,用术后多圈反向螺旋扫描评估螺钉皮质穿破分级和螺钉角度误差(轴向和矢状面,2名观察者)。
关键影像表现/征象
- 多圈反向螺旋扫描由C臂顺时针和逆时针系列旋转联合同步程序化检查床平移组成。
- 几何模体实测与真实尺寸差异0.2±0.1 mm、角度差异0.2±0.1度,提示亚毫米和角度级精度且无失真。
- 羊尸体胸椎螺钉术后多圈反向螺旋扫描识别4处皮质穿破,经术后CT确认。
诊断标准与关键数值
- 多圈反向螺旋扫描纵向覆盖从17 cm增至80 cm,增加370%,扫描时间100秒。
- 螺钉置入角度(n=22)术后多圈反向螺旋扫描与CT直接比较,2名专家观察者测量平均差异轴向3.3±2.6度、矢状面1.9±1.5度。
- 所有测量(轴向和矢状面)在所有扫描类型(常规CT、多圈反向螺旋、常规CBCT)的观察者间ICC均高于0.900。
局限性
- 原文未报告局限性。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
英文原文(摘要)· 点击展开
OBJECTIVES: Cone beam computed tomography (CBCT) imaging is becoming an indispensable intraoperative tool; however, the current field of view prevents visualization of long anatomical sites, limiting clinical utility. Here, we demonstrate the longitudinal extension of the intraoperative CBCT field of view using a multi-turn reverse helical scan and assess potential clinical utility in interventional procedures.
MATERIALS AND METHODS: A fixed-room robotic CBCT imaging system, with additional real-time control, was used to implement a multi-turn reverse helical scan. The scan consists of C-arm rotation, through a series of clockwise and anticlockwise rotations, combined with simultaneous programmed table translation. The motion properties and geometric accuracy of the multi-turn reverse helical imaging trajectory were examined using a simple geometric phantom. To assess potential clinical utility, a pedicle screw posterior fixation procedure in the thoracic spine from T1 to T12 was performed on an ovine cadaver. The multi-turn reverse helical scan was used to provide postoperative assessment of the screw insertion via cortical breach grading and mean screw angle error measurements (axial and sagittal) from 2 observers. For all screw angle measurements, the intraclass correlation coefficient was calculated to determine observer reliability.
RESULTS: The multi-turn reverse helical scans took 100 seconds to complete and increased the longitudinal coverage by 370% from 17 cm to 80 cm. Geometric accuracy was examined by comparing the measured to actual dimensions (0.2 ± 0.1 mm) and angles (0.2 ± 0.1 degrees) of a simple geometric phantom, indicating that the multi-turn reverse helical scan provided submillimeter and degree accuracy with no distortion. During the pedicle screw procedure in an ovine cadaver, the multi-turn reverse helical scan identified 4 cortical breaches, confirmed via the postoperative CT scan. Directly comparing the screw insertion angles (n = 22) measured in the postoperative multi-turn reverse helical and CT scans revealed an average difference of 3.3 ± 2.6 degrees in axial angle and 1.9 ± 1.5 degrees in the sagittal angle from 2 expert observers. The intraclass correlation coefficient was above 0.900 for all measurements (axial and sagittal) across all scan types (conventional CT, multi-turn reverse helical, and conventional CBCT), indicating excellent reliability between observers.
CONCLUSIONS: Extended longitudinal field-of-view intraoperative 3-dimensional imaging with a multi-turn reverse helical scan is feasible on a clinical robotic CBCT imaging system, enabling long anatomical sites to be visualized in a single image, including in the presence of metal hardware.
引用
- Reynolds, Ma, Kanawati, et al. Extended Intraoperative Longitudinal 3-Dimensional Cone Beam Computed Tomography Imaging With a Continuous Multi-Turn Reverse Helical Scan. Invest Radiol. 2022. PMID: 35510875. doi:10.1097/RLI.0000000000000885
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。