文献速递儿科影像神经技术与安全CT

患者特异性儿童头部拟人化CT体模的3D制作与多设备验证

3D Fabrication and Multiscanner CT Validation of a Novel Patient-Specific Anthropomorphic Pediatric Head Phantom.
PubMed 文献 · Acad Radiol · 2026-08-24

本研究利用5岁患儿回顾性头部CT数据制作患者特异性、异质性儿童头部拟人化体模,并评估其在多台CT上的表现。体模各解剖结构采用等效组织环氧树脂与聚氨酯泡沫构建,并通过GATE模拟与XMuDat验证材料衰减特性。结果显示体模在多台设备上CT值稳定,80 kVp下设备间一致性高(ICC=0.992),可用于定量成像验证与扫描方案优化。

要点

  • 该体模范式可用于儿童头部CT低剂量方案优化与跨设备一致性测试。
  • 骨质结构在不同设备间HU值范围较宽(512.0–1285.0 HU),报告时可注意设备差异。
  • 脑脊液与软组织CT值范围存在重叠倾向,区分时需结合解剖位置。

核心结论

  • 该工作流程可制作解剖结构逼真、放射学异质且跨平台CT表现稳定的儿童头部体模。
  • 体模支持定量成像验证、扫描仪协调与扫描方案优化研究。

研究设计与样本

  • 研究类型为体模研制与多设备验证研究,纳入1例5岁患儿的回顾性头部CT数据。
  • 通过分割颅骨、下颌骨、牙齿、脑、脑室、眼球、颈椎与椎管生成体模模型。
  • 采用聚乳酸阳模与硅胶阴模铸造各解剖结构的组织等效环氧树脂复合材料。
  • 使用聚氨酯泡沫保持生理性空气腔,通过GATE蒙特卡洛模拟与XMuDat评估材料衰减特性。
  • 体模在3个厂家共4台CT系统上完成扫描,评估CT值、重复性与设备间一致性。

关键影像表现/征象

  • 骨质结构CT值范围为512.0–1285.0 HU,软组织区域为19.1–65.3 HU。
  • 脑脊液CT值范围为1.2–17.9 HU,空气腔为-1023.9至-903.7 HU。
  • 在80 kVp下总体设备间一致性高,组内相关系数为0.992。

诊断标准与关键数值

  • 10 keV时骨与牙齿等效材料质量衰减系数最高,分别为13.99与18.01 cm²/g。
  • 所有材料在150 keV时质量衰减系数收敛至约0.14–0.15 cm²/g。
  • 80 kVp条件下总体设备间一致性以ICC=0.992作为定量指标。

临床应用与阅片要点

  • 该体模可作为儿科头部CT定量指标验证与设备校准的解剖学真实替代工具。
  • 用于比较不同CT系统间HU值漂移时,可参照本研究中各解剖结构的HU参考区间。
  • 制作流程采用间接铸造策略,理论上可在具备3D打印与模具条件的机构复现。

局限性

  • 体模仅来源于1例患儿,个体解剖代表性有限。
  • 缺乏不同年龄、不同病理状态下的验证。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

英文原文(摘要)· 点击展开

RATIONALE AND OBJECTIVES: Anthropomorphic pediatric computed tomography (CT) phantoms are valuable tools for quantitative imaging validation and protocol optimization, however, available models are often generic, anatomically simplified, or difficult to reproduce, limiting their ability to represent patient-specific pediatric anatomy. This study aimed to develop a patient-specific, heterogeneous anthropomorphic pediatric head phantom using an indirect fabrication strategy and to validate its radiological performance across multiple CT scanners.

MATERIALS AND METHODS: A retrospective head CT dataset from a 5-year-old child was segmented to generate models of the skull, mandible, teeth, brain, ventricles, eyes, cervical vertebrae, and spinal canal. Polylactic acid positive models and silicone negative molds were used to cast compartment-specific tissue-equivalent epoxy composites, while polyurethane foam preserved physiological air cavities. Material attenuation was assessed using Geant4 Application for Tomographic Emission (GATE) Monte Carlo simulations and XMuDat data from 10 to 150 keV. The completed phantom was scanned on four CT systems from three vendors. CT numbers, measurement reproducibility, and interscanner agreement were evaluated.

RESULTS: GATE and XMuDat showed close agreement. At 10 keV, bone- and teeth-equivalent materials had the highest mass attenuation coefficients, at 13.99 and 18.01 cm² g⁻¹, respectively, while all materials converged to approximately 0.14-0.15 cm² g⁻¹ at 150 keV. Across scanners, osseous structures ranged from 512.0 to 1285.0 HU, soft-tissue regions from 19.1 to 65.3 HU, cerebrospinal fluid from 1.2 to 17.9 HU, and air cavities from -1023.9 to -903.7 HU. Overall interscanner agreement at 80 kVp was high (intraclass correlation coefficient = 0.992).

CONCLUSION: The proposed workflow produced an anatomically realistic, radiologically heterogeneous pediatric head phantom with stable cross-platform CT behavior, supporting quantitative validation, scanner harmonization, and protocol-optimization studies.

来源:Acad Radiol,查看原文。版权归原作者所有。

引用

  1. Sekkat, El Mouden, Madkouri, et al. 3D Fabrication and Multiscanner CT Validation of a Novel Patient-Specific Anthropomorphic Pediatric Head Phantom. Acad Radiol. 2026. PMID: 42637581. doi:10.1016/j.acra.2026.08.036

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。