产前三维超声结合3D打印诊断胎儿异常的可行性分析
这项回顾性研究纳入12例存在唇腭裂、脊柱、心脏或脑部异常的胎儿,评估产前三维超声建模并3D打印的尺寸精度,并通过40名资深超声医生和40名研究生的问卷分析其诊断准确性。结果显示打印偏差在一致性界限内(P > .05),3D打印联合三维超声使医生平均误诊率从5%降至0.4%,学生从17.9%降至5.2%。
要点
- 3D打印模型与原始图像尺寸偏差在一致性界限内,精度可接受。
- 3D打印联合3DUS可降低胎儿异常诊断的误诊率。
- 多数医生和学生认为3D打印能精确呈现胎儿异常。
核心结论
- 基于产前三维超声的建模和3D打印误差在可接受范围内,且能改善多种胎儿异常的诊断。
研究设计与样本
- 回顾性研究纳入12例初诊为唇腭裂、脊柱、心脏或脑部异常的胎儿,行三维超声检查、建模及3D打印,并分析打印尺寸精度。
关键影像表现/征象
- 所有原始图像与最终3D打印件之间的偏差(平均偏差0.1 mm)均在一致性界限(-1.12, 1.31 mm)内(P > .05)。
诊断标准与关键数值
- 3D打印联合3DUS与单独3DUS相比,医生的平均误诊率从5%降至0.4%,学生的平均误诊率从17.9%降至5.2%。
- 90.8%的医生和94.2%的学生强烈同意3D打印能精确呈现和描绘胎儿异常。
临床应用与阅片要点
- 3D打印联合三维超声可作为辅助手段,帮助降低胎儿异常诊断的误诊率。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
英文原文(摘要)· 点击展开
OBJECTIVE: To assess the feasibility and accuracy of 3D printing with prenatal three-dimensional ultrasound (3DUS) in the diagnosis of fetal abnormalities.
METHODS: Fetuses initially diagnosed with various abnormalities were included in this retrospective study. The fetuses were examined by 3DUS, modeled, and 3D printed, and the dimensional accuracy of the 3D prints was analyzed. The effectiveness, demand, necessity of 3D printing, and the diagnostic accuracy of different methods were analyzed based on questionnaire responses from 40 senior ultrasound doctors and 40 postgraduate students.
RESULTS: A total of 12 fetuses with cleft lip and palate, spinal, heart, or brain abnormalities were included for detailed assessment. All deviations (mean deviation: 0.1 mm) between the original images and the final 3D prints lay within the consistency boundary (-1.12, 1.31 mm) (P > .05). In the subsequent analyses, 90.8% of the doctors and 94.2% of the students strongly agreed that 3D printing could precisely represent and depict fetal abnormalities. The average misdiagnosis rate of the doctors decreased from 5% to 0.4% after the application of 3D printing combined with 3DUS in comparison with 3DUS alone, and the corresponding value for the students dropped from 17.9% to 5.2%.
CONCLUSIONS: The errors in modeling and 3D printing based on 3DUS were within acceptable limits, and 3D printing improved the diagnosis of various fetal abnormalities.
引用
- Liang J, Ma Q, Zhao X, et al. Feasibility Analysis of 3D Printing With Prenatal Ultrasound for the Diagnosis of Fetal Abnormalities. J Ultrasound Med. 2021. PMID: 34510491. doi:10.1002/jum.15821
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。