1.5特斯拉磁场中金属植入物周围磁共振成像:从基础到高级技术及临床影响
该综述讨论金属植入物周围磁共振成像的伪影控制,指出伪影严重程度取决于植入物材料、尺寸、几何形状和方向以及采集技术。作者总结1.5T优于3.0T、快速自旋回波优于自旋回波或梯度回波、高接收带宽、小体素和短tau反转恢复脂肪抑制等基础策略可减轻伪影,而大型骨科植入物常需切片编码金属伪影校正或多采集可变共振图像组合等进一步优化方法,1.5T磁共振现被广泛认为是金属植入物患者临床评估的首选模态。
要点
- 1.5T较3.0T、快速自旋回波较自旋回波或梯度回波、高接收带宽、小体素和短tau反转恢复脂肪抑制可减轻金属伪影。
- 大型骨科植入物常需切片编码金属伪影校正或多采集可变共振图像组合等进一步优化方法。
- 1.5T磁共振现被广泛认为是金属植入物患者临床评估的首选模态。
核心结论
- 1.5T磁共振结合基础及高级金属伪影减少技术,现被广泛认为是金属植入物患者临床评估的首选模态。
研究设计与样本
- 综述,讨论金属伪影减少技术从基础到高级及其临床影响;原文未报告纳入文献的检索范围与样本量。
诊断标准与关键数值
- 经验法则:选择1.5T而非3.0T磁体、快速自旋回波而非自旋回波或梯度回波序列、高接收带宽、小体素和基于短tau反转恢复的脂肪抑制可减轻金属伪影对诊断图像质量的影响。
- 大型骨科植入物(如关节置换)常需切片编码金属伪影校正或多采集可变共振图像组合等进一步优化的伪影减少方法。
- 金属伪影严重程度取决于植入物材料(尤其是磁化率和电导率)、尺寸、几何形状和在磁体中的方向,以及采集侧的磁场强度、成像脉冲序列和多个采集参数。
临床应用与阅片要点
- 对金属植入物周围组织成像时,可按经验法则优先选择1.5T、快速自旋回波、高接收带宽、小体素和短tau反转恢复脂肪抑制。
- 对大型骨科植入物(如关节置换)的临床评估,可进一步采用切片编码金属伪影校正或多采集可变共振图像组合等优化方法。
- 金属植入物术后并发症(如假体周围感染、材料磨损诱导的滑膜炎、骨溶解或软组织损伤)的早期检出中,磁共振因软组织对比和横断面成像特点而有价值。
局限性
- 原文未报告局限性。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
英文原文(摘要)· 点击展开
During the last decade, metal artifact reduction in magnetic resonance imaging (MRI) has been an area of intensive research and substantial improvement. The demand for an excellent diagnostic MRI scan quality of tissues around metal implants is closely linked to the steadily increasing number of joint arthroplasty (especially knee and hip arthroplasties) and spinal stabilization procedures. Its unmatched soft tissue contrast and cross-sectional nature make MRI a valuable tool in early detection of frequently encountered postoperative complications, such as periprosthetic infection, material wear-induced synovitis, osteolysis, or damage of the soft tissues. However, metal-induced artifacts remain a constant challenge. Successful artifact reduction plays an important role in the diagnostic workup of patients with painful/dysfunctional arthroplasties and helps to improve patient outcome. The artifact severity depends both on the implant and the acquisition technique. The implant's material, in particular its magnetic susceptibility and electrical conductivity, its size, geometry, and orientation in the MRI magnet are critical. On the acquisition side, the magnetic field strength, the employed imaging pulse sequence, and several acquisition parameters can be optimized. As a rule of thumb, the choice of a 1.5-T over a 3.0-T magnet, a fast spin-echo sequence over a spin-echo or gradient-echo sequence, a high receive bandwidth, a small voxel size, and short tau inversion recovery-based fat suppression can mitigate the impact of metal artifacts on diagnostic image quality. However, successful imaging of large orthopedic implants (eg, arthroplasties) often requires further optimized artifact reduction methods, such as slice encoding for metal artifact correction or multiacquisition variable-resonance image combination. With these tools, MRI at 1.5 T is now widely considered the modality of choice for the clinical evaluation of patients with metal implants.
引用
- Germann C, Nanz D, Sutter R, et al. Magnetic Resonance Imaging Around Metal at 1.5 Tesla: Techniques From Basic to Advanced and Clinical Impact. Invest Radiol. 2021. PMID: 34074944. doi:10.1097/RLI.0000000000000798
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。