文献速递心血管CT

新型可切除心肌模型:混合三维打印与硅胶模塑用于心尖肥厚型心肌病模拟心肌切除术

Novel Resectable Myocardial Model Using Hybrid Three-Dimensional Printing and Silicone Molding for Mock Myectomy for Apical Hypertrophic Cardiomyopathy.
PubMed 文献 · Korean J Radiol · 2021-04-01

本研究利用心脏CT舒张末期图像构建三例心尖肥厚型心肌病患者的三维心肌模型,采用混合三维打印与硅胶模塑方法制作可切除心肌模型,并用于模拟手术。模型心肌厚度及左心室心肌质量、腔室体积与CT测量一致,模拟切除的硅胶体积和重量与实际切除心肌相似。提示该模型有助于确定手术范围并规划手术。

要点

  • 混合三维打印与硅胶模塑可制作出与CT解剖一致的可切除心肌模型。
  • 模型可用于模拟心肌切除术,帮助确定切口位置和心肌切除范围。
  • 模拟切除的硅胶体积和重量与实际切除心肌相近。

核心结论

  • 混合三维打印与硅胶模塑制作的心肌模型可能有助于确定心尖肥厚型心肌病的手术范围,并作为手术预演平台指导手术规划。

研究设计与样本

  • 研究纳入2019年1月至2020年5月间三例心尖肥厚型心肌病患者,基于舒张末期心脏CT图像构建三维模型。
  • 采用计算机辅助设计防止硅胶注射时结构变形,通过三维打印复制解剖细节及左心室心肌团块模具。
  • 比较模型图像与心脏CT图像的心肌厚度、左心室心肌质量和腔室体积,并由外科医生进行模拟手术,比较切除硅胶与心肌的体积和重量。

关键影像表现/征象

  • 模型心肌厚度与CT测量的平均差异在基底段、中段、心尖段和心尖部分别为0.3、1.0、6.9和7.3 mm。
  • 左心室心肌质量和腔室体积的平均差异在基底段、中段和心尖段分别为36.9 mL和14.8 mL、2.9 mL和-9.4 mL、6.0 mL和-3.0 mL。
  • 模拟切除的硅胶体积和重量与切除心肌相似,患者2为硅胶6 mL(6.2 g)对应心肌5 mL(5.3 g),患者3为硅胶12 mL(12.5 g)对应心肌11.2 mL(11.8 g)。

临床应用与阅片要点

  • 该模型可作为心尖肥厚型心肌病术前规划工具,帮助术者确定切口位置和心肌切除范围。
  • 阅片时可关注舒张末期CT图像中心肌厚度的准确测量,为模型构建提供依据。

局限性

  • 研究仅纳入三例患者,样本量小。
  • 模型基于心脏CT图像构建,未评估其他影像模态或更大队列中的适用性。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

英文原文(摘要)· 点击展开

OBJECTIVE: We implemented a novel resectable myocardial model for mock myectomy using a hybrid method of three-dimensional (3D) printing and silicone molding for patients with apical hypertrophic cardiomyopathy (ApHCM).

MATERIALS AND METHODS: From January 2019 through May 2020, 3D models from three patients with ApHCM were generated using the end-diastolic cardiac CT phase image. After computer-aided designing of measures to prevent structural deformation during silicone injection into molding, 3D printing was performed to reproduce anatomic details and molds for the left ventricular (LV) myocardial mass. We compared the myocardial thickness of each cardiac segment and the LV myocardial mass and cavity volumes between the myocardial model images and cardiac CT images. The surgeon performed mock surgery, and we compared the volume and weight of the resected silicone and myocardium.

RESULTS: During the mock surgery, the surgeon could determine an ideal site for the incision and the optimal extent of myocardial resection. The mean differences in the measured myocardial thickness of the model (0.3, 1.0, 6.9, and 7.3 mm in the basal, midventricular, apical segments, and apex, respectively) and volume of the LV myocardial mass and chamber (36.9 mL and 14.8 mL, 2.9 mL and -9.4 mL, and 6.0 mL and -3.0 mL in basal, mid-ventricular and apical segments, respectively) were consistent with cardiac CT. The volume and weight of the resected silicone were similar to those of the resected myocardium (6 mL [6.2 g] of silicone and 5 mL [5.3 g] of the myocardium in patient 2; 12 mL [12.5 g] of silicone and 11.2 mL [11.8 g] of the myocardium in patient 3).

CONCLUSION: Our 3D model created using hybrid 3D printing and silicone molding may be useful for determining the extent of surgery and planning surgery guided by a rehearsal platform for ApHCM.

来源:Korean J Radiol,查看原文。版权归原作者所有。

引用

  1. Kim W, Lim M, Jang YJ, et al. Novel Resectable Myocardial Model Using Hybrid Three-Dimensional Printing and Silicone Molding for Mock Myectomy for Apical Hypertrophic Cardiomyopathy. Korean J Radiol. 2021. PMID: 33856135. doi:10.3348/kjr.2020.1164

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。