文献速递头颈骨肌CT

利用3D打印模型制作模具以塑形植入物用于眶壁骨折手术修复

Use of 3D Printed Models to Create Molds for Shaping Implants for Surgical Repair of Orbital Fractures.
PubMed 文献 · Acad Radiol · 2019-08-27

本文描述一种利用三维打印技术定制商用可吸收植入物形状的方法,并回顾3例使用3D打印模具修复眶壁骨折的早期经验。结果显示3例患者术后水肿减轻、眼球偏斜/斜视快速消退,手术时间从标准植入物的平均93.3分钟降至采用3D打印模具后的48.3分钟。

要点

  • 3D打印模具可依据健侧镜像与骨折侧叠加图像定制可吸收植入物形状。
  • 3例患者使用3D打印模具修复眶壁骨折后结局优良,术后水肿减轻。
  • 手术时间从标准植入物平均93.3分钟降至3D打印模具的48.3分钟。

核心结论

  • 三维打印模型可用于制作模具,塑形生物可吸收植入物以实现定制化手术修复,改善贴合度、减少组织操作与术后水肿,并缩短手术时间。

研究设计与样本

  • 回顾性早期经验,纳入3例使用3D打印模具进行眶壁骨折修复的病例,并回顾机构病历评估眶底爆裂性骨折修复的手术时间;采用薄层CT图像载入临床3D可视化软件创建立体光刻模型,经镜像健侧与骨折侧叠加后制作可灭菌3D打印模具。

临床应用与阅片要点

  • 作者描述利用薄层CT图像创建健侧镜像并与骨折侧叠加的虚拟模型,据此制作可灭菌3D打印模具。
  • 作者报告3例使用3D打印模具的患者结局优良,术后水肿减轻、眼球偏斜/斜视快速消退。
  • 作者报告手术时间从标准植入物的平均93.3分钟降至采用3D打印模具后的48.3分钟。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

英文原文(摘要)· 点击展开

RATIONALE AND OBJECTIVES: Surgical repair of an isolated orbital fracture requires anatomically accurate implant shape and placement. We describe a three-dimensional (3D) printing technique to customize the shape of commercially available absorbable implants.

MATERIALS AND METHODS: We reviewed our early experience with three cases in which 3D printed molds were utilized for fracture repair. The institution's medical records were reviewed to assess operative time for orbital floor blow-out fracture repairs. Thin section computed tomography (CT) images were loaded into a clinical 3D visualization software, and stereolithography models were created. The models were loaded into stereolithography editing software in which the nonfractured side was mirrored and overlaid with the fractured side. Sterilizable 3D printed molds were created using the fracture images as well as the virtual mirrored images. The molds were taken to the operating room and used to shape a customized orbital implant for fracture repair, using off-the-shelf bioabsorbable implants.

RESULTS: The three patients treated using 3D printed molds had excellent outcomes, with decreased postoperative edema and rapid resolution of ocular misalignment/strabismus. Surgical times were decreased from an average of 93.3 minutes using standard implants to 48.3 minutes following adoption of 3D printed molds.

CONCLUSION: Three-dimensional printed models can be used to create molds for shaping bioabsorbable implants for customized surgical repair, improving fit, reducing tissue handling and postoperative edema, and reducing surgical times.

来源:Acad Radiol,查看原文。版权归原作者所有。

引用

  1. Weadock WJ, Heisel CJ, Kahana A, et al. Use of 3D Printed Models to Create Molds for Shaping Implants for Surgical Repair of Orbital Fractures. Acad Radiol. 2019. PMID: 31466890. doi:10.1016/j.acra.2019.06.023

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。