文献速递泌尿生殖介入CT

用于机器人辅助肾部分切除术的三维打印医学模型准确性测量

Measurement of the Accuracy of 3D-Printed Medical Models to Be Used for Robot-Assisted Partial Nephrectomy.
PubMed 文献 · AJR Am J Roentgenol · 2019-05-07

本研究纳入2017年12月至2018年3月接受三维打印模型辅助机器人辅助肾部分切除术的患者16例,基于术前CT制作含血管、尿路、实质和肿瘤成分的三维打印肾模型并再次扫描。初始CT与三维打印肾之间肾长轴中位变异1.8%、肿瘤长轴2.35%、肿瘤体积14.7%,16个模型中14个(87.5%)被两位读者评为4分及以上并认为有效;作者结论为三维打印模型在解剖上准确,但手术辅助的可靠性仍需评估。

要点

  • 肿瘤体积在CT与三维打印模型间中位变异14.7%(IQR 11.5-25.2%),大于长度测量变异。
  • 16个三维打印模型中14个(87.5%)被两位读者评为4分及以上,认为有效。
  • 肾长轴中位变异1.8%、肿瘤长轴2.35%、动脉分支间距中位变异1.8%。

核心结论

  • 三维打印模型在解剖上准确,但三维打印模型辅助手术的可靠性仍需评估。

研究设计与样本

  • 研究纳入接受三维打印辅助机器人辅助肾部分切除术并具备匿名CT的患者16例,时间范围为2017年12月至2018年3月;基于术前CT用专用软件和三维打印机制作含血管、尿路、实质和肿瘤成分的模型后对其扫描,在术前CT与三维模型CT上盲法测量肾和肿瘤长轴及肿瘤体积,每例患者行动脉分支间三次对比测量,并以Likert量表评估动脉分布相关性。

诊断标准与关键数值

  • 初始CT与三维打印肾之间肾长轴中位变异1.8%(IQR 0.8-4.23%),肿瘤长轴中位变异2.35%(IQR 0.45-8.6%),肿瘤体积中位变异14.7%(IQR 11.5-25.2%);每肾三次动脉分支间测量中位变异1.8%(IQR 1-3.25%);16个模型中14个(87.5%)被两位读者评为4分及以上并认为有效。

临床应用与阅片要点

  • 作者结论为三维打印模型在解剖上准确,并指出三维打印模型辅助手术的可靠性仍需评估。

局限性

  • 原文未报告局限性。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

英文原文(摘要)· 点击展开

OBJECTIVE. Three-dimensional printing is being used for surgical assistance, particularly for robot-assisted partial nephrectomy (RAPN). The objective of this study was to assess the anatomic accuracy of the 3D model used for 3D model-guided RAPN. SUBJECTS AND METHODS. The study included patients who underwent RAPN aided by 3D printing and anonymized CT. The model, based on preoperative CT with specialized software and a 3D printer, included vascular, urinary, parenchymal, and tumoral elements. It was then scanned. The major axis of the kidney and tumor and the volume of the tumor were measured blindly on the preoperative CT scan and the CT scan of the 3D model. Three comparative measurements between arterial branches were performed for each patient. The correlation of the arterial distribution between the scanner and the 3D model was evaluated on a Likert scale. RESULTS. A total of 16 patients were included between December 2017 and March 2018. The median tumor size was 4.7 cm (interquartile range [IQR], 3.9-6.5 cm). Between the initial CT scan and the 3D printed kidney, the major renal axis varied a median of 1.8% (IQR, 0.8-4.23%), major tumor axis varied 2.35% (IQR, 0.45-8.6%), and the tumor volume varied 14.7% (IQR, 11.5-25.2%). The median arterial interbranch measurement (three measurements performed on each kidney) was 1.8% (IQR, 1-3.25%). Fourteen of 16 (87.5%) 3D printed models had a score of 4 or higher by two readers and were considered valid. CONCLUSION. Three-dimensional printed models are accurate with respect to anatomic reality. The reliability of surgical assistance with 3D printed models must be evaluated.

来源:AJR Am J Roentgenol,查看原文。版权归原作者所有。

引用

  1. Michiels C, Jambon E, Bernhard JC, et al. Measurement of the Accuracy of 3D-Printed Medical Models to Be Used for Robot-Assisted Partial Nephrectomy. AJR Am J Roentgenol. 2019. PMID: 31063426. doi:10.2214/AJR.18.21048

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。