文献速递骨肌介入CTDR

用于透视引导肩关节造影的盂肱关节原型组装3D打印体模

A prototype assembled 3D-printed phantom of the glenohumeral joint for fluoroscopic-guided shoulder arthrography.
PubMed 文献 · Skeletal Radiol · 2018-06-09

研究描述了从正常肩部CT关节造影图像中提取骨性结构、关节内间隙和皮肤表面,分别用石膏、橡胶类材料和聚酰胺打印并组装成盂肱关节体模,用于透视引导肩关节造影训练。体模可重复用于前、后及肩袖间隙三种入路操作,并模拟了体内针引导的挑战,作者认为该模型可作为有价值的训练工具。

要点

  • 3D打印盂肱关节体模可模拟体内骨皮质与髓质分化,并集成盂唇于打印关节囊内。
  • 体模可重复用于透视引导下前、后及肩袖间隙入路肩关节造影操作训练。
  • 作者认为该复杂关节囊3D打印体模可作为有价值的训练工具。

核心结论

  • 采用该技术可3D打印复杂关节囊(如盂肱关节),该体模可作为有价值的训练工具。

研究设计与样本

  • 技术描述类研究,从正常肩部CT关节造影图像中数字化提取骨性结构、关节内间隙和皮肤表面,分别用石膏(粘合剂喷射)、橡胶类TangoPlus材料(PolyJet)、聚酰胺(选择性激光烧结)打印并组装成体模,行透视引导肩关节造影及CT关节造影成像。

关键影像表现/征象

  • 不透X线的骨性结构复制了体内骨皮质与髓质分化,表现为致密皮质骨和密度较低的髓质松质骨。
  • 盂唇成功整合入打印的关节囊,并在CT关节造影上可见。
  • 体模可重复用于前、后及肩袖间隙三种常规入路肩关节造影,并模拟了体内针引导的挑战。

临床应用与阅片要点

  • 作者认为该体模可作为透视引导下肩关节造影训练的有价值工具。

局限性

  • 原文未报告局限性

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

英文原文(摘要)· 点击展开

PURPOSE: To describe the methodology of constructing a three-dimensional (3D) printed model of the glenohumeral joint, to serve as an interventional phantom for fluoroscopy-guided shoulder arthrography training.

MATERIALS AND METHODS: The osseous structures, intra-articular space and skin surface of the shoulder were digitally extracted as separate 3D meshes from a normal CT arthrogram of the shoulder, using commercially available software. The osseous structures were 3D-printed in gypsum, a fluoroscopically radiopaque mineral, using binder jet technology. The joint capsule was 3D printed with rubber-like TangoPlus material, using PolyJet technology. The capsule was secured to the humeral head and glenoid to create a sealed intra-articular space. A polyamide mold of the skin was printed using selective laser sintering. The joint was stabilized inside the mold, and the surrounding soft tissues were cast in silicone of varying densities. Fluoroscopically-guided shoulder arthrography was performed using anterior, posterior, and rotator interval approaches. CT arthrographic imaging of the phantom was also performed.

RESULTS: A life-size phantom of the glenohumeral joint was constructed. The radiopaque osseous structures replicated in-vivo osseous corticomedullary differentiation, with dense cortical bone and less dense medullary cancellous bone. The glenoid labrum was successfully integrated into the printed capsule, and visualized on CT arthrography. The phantom was repeatedly used to perform shoulder arthrography using all three conventional approaches, and simulated the in vivo challenges of needle guidance.

CONCLUSIONS: 3D printing of a complex capsule, such as the glenohumeral joint, is possible with this technique. Such a model can serve as a valuable training tool.

来源:Skeletal Radiol,查看原文。版权归原作者所有。

引用

  1. Javan R, Ellenbogen AL, Greek N, et al. A prototype assembled 3D-printed phantom of the glenohumeral joint for fluoroscopic-guided shoulder arthrography. Skeletal Radiol. 2018. PMID: 29948036. doi:10.1007/s00256-018-2979-4

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。