文献速递心血管介入CTUS

3D打印心脏模型引导左心耳封堵:临床实践中有用吗

3D-printed heart model to guide LAA closure: useful in clinical practice?
PubMed 文献 · Eur Radiol · 2018-06-14

研究纳入15例拟用Amulet装置行左心耳封堵的患者,基于心脏CT分割左心耳并打印个性化3D模型(P3DPM)以预测装置尺寸,并与经食管超声(TEE)、CT预测及实际植入尺寸比较;P3DPM预测的装置尺寸在全部患者中准确,TEE和CT预测分别有8/15(53%)和10/15(67%)与实际植入尺寸相符。

要点

  • P3DPM预测的Amulet尺寸在15例中全部准确,与左心耳壁完美接触。
  • 3D-TEE预测尺寸与实际植入相符8/15(53%),CT相符10/15(67%)。
  • P3DPM-CT可显示装置变形及封堵盘与肺静脉的位置关系。

核心结论

  • P3DPM可模拟左心耳封堵过程,有助于确定Amulet的最佳尺寸及在左心耳内的位置。

研究设计与样本

  • 研究纳入15例拟行左心耳封堵的Amulet装置患者(年龄75.4±8.5岁),术前行心脏CT,用Vitrea®软件半自动分割左心耳,以1.5 mm厚壳导出并采用TangoPlus柔性材料打印P3DPM。

诊断标准与关键数值

  • P3DPM预测的装置尺寸在全部15例患者中准确,与左心耳壁完美接触,无装置不稳或过度压缩。
  • 3D-TEE预测的装置尺寸与实际植入尺寸相符8/15(53%)。
  • CT预测的装置尺寸与实际植入尺寸相符10/15(67%)。

临床应用与阅片要点

  • 作者认为P3DPM可模拟左心耳封堵过程,帮助识别Amulet的最佳尺寸和在左心耳内的位置。
  • 作者认为3D打印心脏模型可能有助于缩短Amulet植入的学习曲线。

局限性

  • 原文未报告局限性。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

英文原文(摘要)· 点击展开

OBJECTIVES: Correct device sizing for left atrial appendage (LAA) closure remains challenging due to complex LAA shapes. The aim of our study was to investigative the utility of personalized 3D-printed models (P3DPM) of the LAA to guide device size selection.

METHODS: Fifteen patients (75.4 ±8.5years) scheduled for LAA closure using an Amulet device underwent cardiac computed tomography (CT). The LAA was segmented by semiautomatic algorithms using Vitrea® software. A 1.5-mm LAA thick shell was exported in stereolithography format and printed using TangoPlus flexible material. Different Amulet device sizes on the P3DPM were tested. New P3DPM-CT with the device was acquired in order to appreciate the proximal disc sealing the LAA ostium and the compression of the distal lobe within the LAA. We predicted the device size with P3DPM and compared this with the device sizes predicted by transesophageal echocardiography (TEE) and CT as well as the device size implanted in patients.

RESULTS: The device size predicted by 3D-TEE and CT corresponded to the implanted device size in 8/15 (53%) and 10/15 (67%), respectively. The predicted device size from the P3DPM was accurate in all patients, obtaining perfect contact with the LAA wall, without device instability or excessive compression. P3DPM-CT with the deployed device showed device deformation and positioning of the disk in relation to the pulmonary veins, allowing us to determine the best device size in all 15 cases.

CONCLUSION: P3DPM allowed us to simulate the LAA closure procedure and thus helped to identify the best Amulet size and position within the LAA.

KEY POINTS: • A 3D-printed heart model allows to simulate the LAA closure procedure. • A 3D-printed heart model allowed to identify the optimal Amulet size and position. • 3D-printed heart models may contribute to reduce the Amulet implantation learning curve.

来源:Eur Radiol,查看原文。版权归原作者所有。

引用

  1. Hachulla AL, Noble S, Guglielmi G, et al. 3D-printed heart model to guide LAA closure: useful in clinical practice? Eur Radiol. 2018. PMID: 29948082. doi:10.1007/s00330-018-5569-x

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。