文献速递心血管介入CT

基于组织模拟3D打印的经导管主动脉瓣置换术后瓣周漏定量预测

Quantitative Prediction of Paravalvular Leak in Transcatheter Aortic Valve Replacement Based on Tissue-Mimicking 3D Printing.
PubMed 文献 · JACC Cardiovasc Imaging · 2017-01-01

本回顾性研究纳入18例TAVR患者,用组织模拟3D打印技术制作患者特异性主动脉根幻影,在体外模拟TAVR并量化瓣环应变。新指标瓣环膨出指数可显著预测中重度瓣周漏(AUC=95%;p<0.0001),并在12例瓣周漏患者中预测9例(准确率75%)的主要漏口位置。

要点

  • 瓣环膨出指数是唯一显著预测中重度瓣周漏的指标(AUC=95%;p<0.0001)。
  • 无瓣周漏、微量至轻度、中重度三组间最大瓣环膨出指数有显著差异(p=0.001)。
  • 在12例术后瓣周漏患者中,瓣环膨出指数预测9例的主要漏口位置(准确率75%)。

核心结论

  • 概念验证研究显示,组织模拟3D打印幻影可在体外定量评估TAVR术后主动脉根应变,瓣环膨出指数在预测瓣周漏的发生、严重程度和位置方面优于其他已知变量,准确率高。

研究设计与样本

  • 回顾性研究,纳入18例接受TAVR的患者,基于术前CT用组织模拟3D打印技术制作患者特异性主动脉根幻影,在幻影中部署CoreValve自膨胀瓣膜模拟TAVR,体外量化术后主动脉根应变。

关键影像表现/征象

  • 在幻影中部署CoreValve瓣膜后量化主动脉根应变,并测量瓣环膨出指数以评估瓣环应变不均匀性。
  • 无瓣周漏、微量至轻度瓣周漏、中重度瓣周漏三组患者的最大瓣环膨出指数存在显著差异(p=0.001)。

诊断标准与关键数值

  • 瓣环膨出指数预测中重度瓣周漏的AUC=95%(p<0.0001),为唯一显著预测指标。
  • 在12例术后瓣周漏患者中,瓣环膨出指数预测主要瓣周漏位置的准确率为75%(9/12)。

临床应用与阅片要点

  • 基于术前CT构建组织模拟3D打印幻影,可用于体外模拟TAVR并定量评估主动脉根应变。
  • 瓣环膨出指数可用于定量预测TAVR术后瓣周漏的发生、严重程度和位置。

局限性

  • 原文未报告局限性。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

英文原文(摘要)· 点击展开

OBJECTIVES: This study aimed to develop a procedure simulation platform for in vitro transcatheter aortic valve replacement (TAVR) using patient-specific 3-dimensional (3D) printed tissue-mimicking phantoms. We investigated the feasibility of using these 3D printed phantoms to quantitatively predict the occurrence, severity, and location of any degree of post-TAVR paravalvular leaks (PVL).

BACKGROUND: We have previously shown that metamaterial 3D printing technique can be used to create patient-specific phantoms that mimic the mechanical properties of biological tissue. This may have applications in procedural planning for cardiovascular interventions.

METHODS: This retrospective study looked at 18 patients who underwent TAVR. Patient-specific aortic root phantoms were created using the tissue-mimicking 3D printing technique using pre-TAVR computed tomography. The CoreValve (self-expanding valve) prostheses were deployed in the phantoms to simulate the TAVR procedure, from which post-TAVR aortic root strain was quantified in vitro. A novel index, the annular bulge index, was measured to assess the post-TAVR annular strain unevenness in the phantoms. We tested the comparative predictive value of the bulge index and other known predictors of post-TAVR PVL.

RESULTS: The maximum annular bulge index was significantly different among patient subgroups that had no PVL, trace-to-mild PVL, and moderate-to-severe PVL (p = 0.001). Compared with other known PVL predictors, bulge index was the only significant predictor of moderate-severe PVL (area under the curve = 95%; p < 0.0001). Also, in 12 patients with post-TAVR PVL, the annular bulge index predicted the major PVL location in 9 patients (accuracy = 75%).

CONCLUSIONS: In this proof-of-concept study, we have demonstrated the feasibility of using 3D printed tissue-mimicking phantoms to quantitatively assess the post-TAVR aortic root strain in vitro. A novel indicator of the post-TAVR annular strain unevenness, the annular bulge index, outperformed the other established variables and achieved a high level of accuracy in predicting post-TAVR PVL, in terms of its occurrence, severity, and location.

来源:JACC Cardiovasc Imaging,查看原文。版权归原作者所有。

引用

  1. Qian Z, Wang K, Liu S, et al. Quantitative Prediction of Paravalvular Leak in Transcatheter Aortic Valve Replacement Based on Tissue-Mimicking 3D Printing. JACC Cardiovasc Imaging. 2017. PMID: 28683947. doi:10.1016/j.jcmg.2017.04.005

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。