文献速递骨肌CT

CT扫描及金属伪影减少策略对测量膝关节植入物位移的影响:iMAR有益还是有害?

The effect of CT scanning and metal artefact reduction strategies on measuring knee implant displacement: iMAR - helpful or harmful?
PubMed 文献 · Eur J Radiol · 2025-07-04

本研究在一具带全膝关节置换的新鲜冰冻尸体腿上进行CT扫描,比较标准方案与四种金属伪影减少策略(增加曝光/管电压、iMAR、Sn滤过、扩展CT标尺重建)对负载诱导植入物位移测量的影响。结果显示增加曝光/管电压、Sn滤过和扩展CT标尺重建不影响测量误差,而iMAR虽提高骨相似性但显著增加旋转误差中位数至0.19°,提示其可能较不适合量化植入物位移。

要点

  • 增加曝光/管电压、Sn滤过和扩展CT标尺重建对植入物位移测量误差无影响。
  • iMAR虽提高骨灰阶相似性(CC=0.99),但使旋转范数中位数显著增至0.19°。
  • 各方案植入物灰阶相似性相当(CC=0.88),iMAR可能较不适合量化植入物位移。

核心结论

  • 增加曝光/管电压、Sn滤过和扩展CT标尺重建不影响基于3D CT的膝关节植入物松动检测的测量误差;iMAR显示旋转误差增加而其他位移参数不变,提示其可能较不适合量化植入物位移。

研究设计与样本

  • 研究采用一具带全膝关节置换的新鲜冰冻尸体腿,使用标准方案和四种金属伪影减少策略(增加曝光/管电压、iMAR、Sn滤过、扩展CT标尺重建)进行CT扫描,每种扫描随机重新摆放腿位置重复10次以确保无植入物-骨运动;图像分析包括植入物和近端胫骨皮质分割、跨扫描对象配准及表观相对位移量化。

关键影像表现/征象

  • 金属伪影减少策略的CT扫描显示噪声和条纹伪影减少。
  • 植入物灰阶相似性在各方案间相似(CC=0.88),iMAR的骨相似性最高(CC=0.99)。

诊断标准与关键数值

  • 植入物位移误差通过平移和旋转范数、平均目标配准误差(mTRE)和最大总点运动(MTPM)测量。
  • 增加曝光/管电压、Sn滤过和扩展CT标尺重建的植入物位移误差相当(中位数:平移0.08 mm,旋转0.13°,mTRE 0.09 mm,MTPM 0.14 mm)。
  • iMAR使旋转范数中位数显著增加至0.19°。

临床应用与阅片要点

  • 原文未据此给出推荐。

局限性

  • 原文未报告局限性。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

英文原文(摘要)· 点击展开

BACKGROUND: A recent development in diagnosing total knee arthroplasty (TKA) tibial component loosening uses Computed Tomography (CT) images of loaded knees to assess implant micro-motion, but metal artefacts can affect reliability. This study investigates the impact of increased exposure and tube voltage, iterative metal artefact reduction reconstruction (iMAR), Sn-filtering and an extended CT scale (ECTS), compared to a standard knee CT protocol on load-induced implant displacement measurement.

METHOD: CT scans of a fresh frozen cadaver leg with a TKA were acquired using a standard protocol and four metal artefact reduction strategies: Increased exposure/tube voltage, iMAR, Sn-filtering, and ECTS reconstruction. Each scan was repeated 10 times with random leg repositioning ensuring no implant-bone motion. Image analysis included implant and proximal tibial cortex segmentation, object registration across scans, and quantification of apparent relative displacement. Grey-level similarity was assessed using the correlation coefficient (CC). Implant displacement error was measured using translation and rotation norms, mean target registration error (mTRE), and maximum total point motion (MTPM).

RESULTS: CT scans with metal artefact reduction showed less noise and streaking. Grey-level similarity of the implant was similar across protocols (CC = 0.88). iMAR had the highest bone similarity (CC = 0.99). Implant displacement errors were comparable for increased exposure/tube voltage, Sn-filtering and ECTS (median: 0.08 mm translation, 0.13° rotation, 0.09 mm mTRE, 0.14 mm MTPM). However, iMAR statistically significantly increased median rotation norm to 0.19˚.

CONCLUSION: Increased exposure/tube voltage, Sn-filtering, and ECTS do not impact the measurement error of 3D CT-based knee implant loosening detection. iMAR showed increased rotational error while other displacement parameters remained unchanged, suggesting it may be less suitable for quantifying implant displacement.

来源:Eur J Radiol,查看原文。版权归原作者所有。

引用

  1. Ter Wee MA, Speelman RPJ, Dobbe JGG, et al. The effect of CT scanning and metal artefact reduction strategies on measuring knee implant displacement: iMAR - helpful or harmful? Eur J Radiol. 2025. PMID: 40645025. doi:10.1016/j.ejrad.2025.112281

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。