使用锡滤过技术的低剂量计算机断层扫描关节造影:推进踝关节高分辨率软骨评估
本研究采用锡滤过技术行100 kVp低剂量CT关节造影(CTA),对39例超声引导下关节腔注射者评估踝关节软骨,记录DLP与CTDIVol,并与MRI及关节镜对比诊断准确性。结果显示平均DLP 19.37 mGy-cm,主观图像质量高(诊断等级1.71,组内相关系数0.966),69.2%病例检出软骨损伤、关节镜确认率78.9%,CTA与MRI结果一致率74.1%。作者认为锡滤过CTA联合超声引导关节腔注射是低辐射、高分辨率的踝关节软骨评估方法。
要点
- 锡滤过CTA平均DLP为19.37 mGy-cm(±4.3),主观图像质量维持高诊断等级1.71。
- 软骨损伤检出率69.2%,关节镜确认率78.9%,CTA与MRI结果一致率74.1%。
- 骨与对比剂的平均CNR分别为97.92(±34.65)和135.24(±68.56)。
核心结论
- 锡滤过CTA联合超声引导关节腔注射是低辐射、高分辨率的踝关节软骨评估方法。
- 其检出细微损伤的能力对手术规划有价值,尤其适用于有金属植入物或MRI结果不确定的患者。
研究设计与样本
- 研究类型为采用锡滤过技术的CT关节造影评估研究。
- 共进行39次超声引导下关节腔注射,未报告并发症。
- 所有患者行管电压100 kVp的锡滤过CTA,记录DLP和CTDIVol。
- 影像结果与MRI及可获得的关节镜对比以评估诊断准确性。
- 由4名独立阅片者按包括软骨损伤诊断适用性在内的多项条目评分主观图像质量。
关键影像表现/征象
- 软骨损伤在69.2%的病例中被识别。
- CTA与MRI所见在74.1%的病例中一致。
诊断标准与关键数值
- 锡滤过CTA平均DLP为19.37 mGy-cm(±4.3)。
- 主观图像质量诊断等级为1.71,组内相关系数为0.966。
- 骨的平均CNR为97.92(±34.65),对比剂的平均CNR为135.24(±68.56)。
- 骨的平均SNR为91.85(±32.74),对比剂的平均SNR为129.18(±67.44)。
- 软骨损伤关节镜确认率为78.9%。
局限性
- 原文未报告局限性。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
英文原文(摘要)· 点击展开
RATIONALE AND OBJECTIVES: Arthrographic imaging is essential for diagnosing and managing joint pathologies. Computed tomography arthrography (CTA) offers high spatial resolution and can complement or replace magnetic resonance imaging (MRI) when needed. Dose-reduction methods are crucial due to the significant radiation exposure from radiological procedures. This study explores the use of tin-filter technology in musculoskeletal radiology to reduce radiation dose without compromising image quality.
MATERIALS AND METHODS: 39 sonographically guided joint fillings were conducted with no reported complications. Tin-filter CTA with tube voltage of 100 kVp was conducted for all patients, with radiation exposure metrics (DLP, CTDIVol) recorded and imaging results compared to MRI and if available arthroscopy for diagnostic accuracy. Four independent readers rated the images subjective quality by a range of different items like diagnostic suitability for assessing cartilage damage. For the objective image assessment, the contrast-to-noise ratio (CNR) and Signal-to noise ratio (SNR) were used.
RESULTS: Tin-filter CTA achieved a mean DLP of 19.37 mGy-cm (± 4.3). High subjective image quality was maintained (diagnostic grade: 1.71; intraclass correlation coefficient: 0.966). The mean CNR was 97.92 (± 34.65) for bone and 135.24 (± 68.56) for the contrast agent. Similarly, the mean SNR was 91.85 (± 32.74) for bone and 129.18 (± 67.44). Cartilage damage was identified in 69.2% of cases, with 78.9% confirmation in arthroscopy. CTA aligned with MRI findings in 74.1% of cases.
CONCLUSION: Tin-filter CTA, combined with sonographically guided joint filling, is a low-radiation, high-resolution method for assessing ankle joint cartilage. Its ability to detect subtle damage makes it invaluable for surgical planning, especially for patients with metal implants or inconclusive MRI results.
引用
- Schmid N, Schüle S, Rienecker M, et al. Low-Dose Computed Tomography Arthrography Using Tin-Filter Technology: Advancing High-Resolution Cartilage Evaluation in the Ankle Joint. Acad Radiol. 2025. PMID: 40312231. doi:10.1016/j.acra.2025.04.039
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。