文献速递主动脉疾病

用于主动脉体外血流动力学评估的模拟循环回路:在主动脉夹层中的应用

A Mock Circulation Loop for In Vitro Hemodynamic Evaluation of Aorta: Application in Aortic Dissection.
PubMed 文献 · J Endovasc Ther · 2021-08-03

本研究构建了整合Windkessel元件与患者特异性硅胶主动脉模型的模拟循环回路(MCL),用于在体外复现主动脉血流环境。通过20名健康志愿者的分支血流数据验证正常主动脉模型的血流分配比(平均差异2.4%±1.70%),并对比正常与夹层模型在静息条件下的压力与流速,发现夹层模型收缩压与舒张压更高,真腔时间平均流速高于假腔。

要点

  • MCL可模拟正常静息与左心衰条件,并量化主动脉分支流速与压力。
  • 正常主动脉模型各分支血流分配比与标准化数据平均差异2.4%±1.70%。
  • 夹层模型收缩压与舒张压高于正常模型,真腔流速高于假腔。

核心结论

  • 所提出的MCL可作为不同生理条件下主动脉疾病体外血流动力学分析的研究工具。

研究设计与样本

  • 建立患者特异性正常与夹层主动脉硅胶模型(含12个分支血管)并嵌入MCL。
  • 以20名健康志愿者的主动脉分支流速作为血流分配的标准化数据。
  • 通过改变边界条件模拟正常静息与左心衰(LHF)条件,并用独立传感器量化分支流速与压力。

主要发现

  • 正常静息条件下模拟心率60 bpm、全身流量4.85 L/min。
  • LHF条件下收缩压75.94±0.77 mmHg、舒张压57.65±0.35 mmHg。
  • 正常主动脉模型各分支血流分配比与标准化数据平均差异2.4%±1.70%。
  • 静息条件下夹层模型收缩压117.82±0.60 vs 108.75±2.26 mmHg、舒张压72.38±0.58 vs 70.46±2.33 mmHg,均高于正常模型。
  • 真腔时间平均流速36.95 cm/s高于假腔22.95 cm/s,真假腔间血流方向在不同再破口处不同。

临床怎么用

  • 可用于体外评估主动脉夹层在不同生理条件下的血流动力学特征。
  • 分支血流分配比验证方法可用于类似体外循环模型的标准化校验。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

PURPOSE: Aortic dissection (AD) is a catastrophic disease with complex hemodynamic conditions, however, understandings regarding its perfusion characteristics were not sufficient. In this study, a mock circulation loop (MCL) that integrated the Windkessel element and patient-specific silicone aortic phantoms was proposed to reproduce the aortic flow environment in vitro. MATERIALS AND METHODS: Patient-specific normal and dissected aortic phantoms with 12 branching vessels were established and embedded into this MCL. Velocities for aortic branches based on 20 healthy volunteers were regarded as the standardized data for flow division. By altering boundary conditions, the proposed MCL could mimic normal resting and left-sided heart failure (LHF) conditions. Flow rates and pressure status of the aortic branches could be quantified by separate sensors. RESULTS: In normal resting condition, the simulated heart rate and systemic flow rate were 60 bpm and 4.85 L/minute, respectively. For the LHF condition, the systolic and diastolic blood pressures were 75.94±0.77 mmHg and 57.65±0.35 mmHg, respectively. By tuning the vascular compliance and peripheral resistance, the flow distribution ratio (FDR) of each aortic branch was validated by the standardized data in the normal aortic phantom (mean difference 2.4%±1.70%). By comparing between the normal and dissected aortic models under resting condition, our results indicated that the AD model presented higher systolic (117.82±0.60 vs 108.75±2.26 mmHg) and diastolic (72.38±0.58 vs 70.46±2.33 mmHg) pressures, the time-average velocity in the true lumen (TL; 36.95 cm/s) was higher than that in the false lumen (FL; 22.95 cm/s), and the blood transport direction between the TL and FL varied in different re-entries. CONCLUSIONS: The proposed MCL could be applied as a research tool for in vitro hemodynamic analysis of the aorta diseases under various physical conditions.

来源:J Endovasc Ther,查看原文。版权归原作者所有。

引用

  1. Chen D, Liang S, Li Z, et al. A Mock Circulation Loop for In Vitro Hemodynamic Evaluation of Aorta: Application in Aortic Dissection. J Endovasc Ther. 2021. PMID: 34342237. doi:10.1177/15266028211034863

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。