文献速递主动脉疾病

胸主动脉几何形态与主动脉腔内移植物鸟嘴样贴壁不良严重程度的相关性

Thoracic aortic geometry correlates with endograft bird-beaking severity.
PubMed 文献 · J Vasc Surg · 2020-02-05

本研究回顾性分析20例接受TEVAR的胸主动脉瘤或B型夹层患者,利用三维几何模型量化术后鸟嘴样贴壁不良(以鸟嘴高度≥5 mm分为BBG组10例与NBBG组10例),发现术前主动脉内曲率×直径为BBG的独立相关几何指标,内曲率及曲率×直径与鸟嘴高度和角度显著相关。

要点

  • 术前主动脉内曲率×直径较高者TEVAR术后鸟嘴样贴壁不良风险增加。
  • 鸟嘴严重程度可用长度、高度和角度三维量化,鸟嘴高度≥5 mm可作为分组阈值。
  • 术前内曲率与曲率×直径与鸟嘴高度和角度显著相关,可用于术前预判。

核心结论

  • TEVAR鸟嘴严重程度可通过几何建模技术量化与预测,术前高主动脉内曲率合并较大直径增加TEVAR鸟嘴样贴壁不良风险。

研究设计与样本

  • 回顾性分析20例胸主动脉瘤或B型夹层接受TEVAR的患者,利用CT构建术前术后主动脉与移植物的三维几何模型。

主要发现

  • 主动脉面积、内曲率、直径在BBG与NBBG间无显著差异,但内曲率×直径在BBG显著更高(1.4 ± 0.5 vs 1.0 ± 0.3;P = .030)。
  • 内曲率与鸟嘴高度相关(R = 0.462,P = .041),曲率×直径与鸟嘴高度相关(R = 0.592,P = .006)。
  • 内曲率与鸟嘴角度相关(R = 0.680,P < .001),曲率×直径与鸟嘴角度相关(R = 0.712,P < .001)。

关键数值与推荐

  • 以鸟嘴高度≥5 mm为阈值分为鸟嘴组(BBG,n = 10)与无鸟嘴组(NBBG,n = 10)。
  • 主动脉面积BBG 1002 ± 118 mm2 vs NBBG 834 ± 248 mm2,差异无统计学意义。
  • 主动脉内曲率BBG 0.040 ± 0.014 mm-1 vs NBBG 0.031 ± 0.012 mm-1,差异无统计学意义。
  • 主动脉直径BBG 35.7 ± 2.1 mm vs NBBG 32.2 ± 4.9 mm,差异无统计学意义。

临床怎么用

  • 术前可基于CT三维几何模型测量主动脉内曲率与直径,评估TEVAR术后鸟嘴样贴壁不良风险。
  • 对高内曲率×直径患者,可提前规划近端锚定区策略并加强术后影像随访。

局限性

  • 回顾性设计且样本量仅20例,结果需更大样本验证。
  • 鸟嘴量化方法依赖三维几何建模,尚未在常规临床流程中验证。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

OBJECTIVE: Aortic geometry has been shown to influence the development of endograft malapposition (bird-beaking) in thoracic endovascular aortic repair (TEVAR), but the extent of this relationship lacks clarity. The aim of this study was to develop a reproducible method of measuring bird-beak severity and to investigate preoperative geometry associated with bird-beaking. METHODS: The study retrospectively analyzed 20 patients with thoracic aortic aneurysms or type B dissections treated with TEVAR. Computed tomography scans were used to construct three-dimensional geometric models of the preoperative and postoperative aorta and endograft. Postoperative bird-beaking was quantified with length, height, and angle; categorized into a bird-beak group (BBG; n = 10) and no bird-beak group (NBBG; n = 10) using bird-beak height ≥5 mm as a threshold; and correlated to preoperative metrics including aortic cross-sectional area, inner curvature, diameter, and inner curvature × diameter as well as graft diameter and oversizing at the proximal landing zone. RESULTS: Aortic area (1002 ± 118 mm2 vs 834 ± 248 mm2), inner curvature (0.040 ± 0.014 mm-1 vs 0.031 ± 0.012 mm-1), and diameter (35.7 ± 2.1 mm vs 32.2 ± 4.9 mm) were not significantly different between BBG and NBBG; however, inner curvature × diameter was significantly higher in BBG (1.4 ± 0.5 vs 1.0 ± 0.3; P = .030). Inner curvature and curvature × diameter were significantly correlated with bird-beak height (R = 0.462, P = .041; R = 0.592, P = .006) and bird-beak angle (R = 0.680, P < .001; R = 0.712, P < .001). CONCLUSIONS: TEVAR bird-beak severity can be quantified and predicted with geometric modeling techniques, and the combination of high preoperative aortic inner curvature and diameter increases the risk for development of TEVAR bird-beaking.

来源:J Vasc Surg,查看原文。版权归原作者所有。

引用

  1. Frohlich MM, Suh GY, Bondesson J, et al. Thoracic aortic geometry correlates with endograft bird-beaking severity. J Vasc Surg. 2020. PMID: 32035770. doi:10.1016/j.jvs.2019.11.045

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。