3D打印动脉瘤模拟器用于EVAR培训
该前瞻性单中心对照研究在巴西大学医院开发基于3D打印动脉瘤的EVAR模拟系统,评估患者特异性术前培训对血管外科住院医师手术表现的影响。结果显示培训组透视时间减少30%、总手术时间减少29%、造影剂用量减少25%,且住院医师认为培训实用、真实并增强自信。
要点
- 患者特异性3D打印模拟器术前培训可减少EVAR透视时间、手术时间和造影剂用量。
- Form1+(柔性树脂)和Makerbot(硅胶)打印机在模拟器质量和成本上表现最佳。
- 住院医师认为培训实用、真实,并提高了自信心。
核心结论
- 基于3D打印动脉瘤的EVAR模拟系统可行,患者特异性术前培训可改善住院医师手术表现并增强自信。
研究设计与样本
- 前瞻性、对照、单中心研究,2015年于巴西圣保罗大学医学院开展,10名血管外科住院医师分对照组(5人30例,2014年)和培训组(5人25例,2015年)。
主要发现
- 住院医师认为培训实用、真实,并报告增强了自信心。
- Form1+(柔性树脂)和Makerbot(硅胶)打印机在模拟器质量和成本上表现最佳。
临床怎么用
- EVAR术前可采用患者特异性3D打印动脉瘤模拟器对住院医师进行培训,以缩短透视和手术时间、减少造影剂用量。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
OBJECTIVES: To develop an endovascular aneurysm repair (EVAR) simulation system using three dimensional (3D) printed aneurysms, and to evaluate the impact of patient specific training prior to EVAR on the surgical performance of vascular surgery residents in a university hospital in Brazil. METHODS: This was a prospective, controlled, single centre study. During 2015, the aneurysms of patients undergoing elective EVAR at São Paulo University Medical School were 3D printed and used in training sessions with vascular surgery residents. The 3D printers Stratasys-Connex 350, Formlabs-Form1+, and Makerbot were tested. Ten residents were enrolled in the control group (five residents and 30 patients in 2014) or the training group (five residents and 25 patients in 2015). The control group performed the surgery under the supervision of a senior vascular surgeon (routine procedure, without simulator training). The training group practised the surgery in a patient specific simulator prior to the routine procedure. Objective parameters were analysed, and a subjective questionnaire addressing training utility and realism was answered. RESULTS: Patient specific training reduced fluoroscopy time by 30% (mean 48 min, 95% confidence interval [CI] 40-58 vs. 33 min, 95% CI 26-42 [p < .01]), total procedure time by 29% (mean 292 min [95% CI 235-336] vs. 207 [95% CI 173-247]; p < .01), and volume of contrast used by 25% (mean 87 mL [95% CI 73-103] vs. 65 mL [95% CI 52-81]; p = .02). The residents considered the training useful and realistic, and reported that it increased their self confidence. The 3D printers Form1+ (using flexible resin) and Makerbot (using silicone) provided the best performance based on simulator quality and cost. CONCLUSION: An EVAR simulation system using 3D printed aneurysms was feasible. The best results were obtained with the 3D printers Form1+ (using flexible resin) and Makerbot (using silicone). Patient specific training prior to EVAR at a university hospital in Brazil improved residents' surgical performance (based on fluoroscopy time, surgery time, and volume of contrast used) and increased their self confidence.
引用
- Torres IO, De Luccia N. A simulator for training in endovascular aneurysm repair: The use of three dimensional printers. Eur J Vasc Endovasc Surg. 2017. PMID: 28647340. doi:10.1016/j.ejvs.2017.05.011
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。