3D打印模板在医师改良移植物开窗定位中的验证
研究描述并台架验证了一种可共享、版本锁定的CAD到3D打印工作流程,用于生成圆柱形模板以指导医师改良移植物(PMEG)开窗定位。使用5例CT血管造影脚本化设计模板,打印54个开窗,中位弧长偏差0.3 mm、高度偏差0.2 mm,树脂类型、打印顺序及靶血管未一致影响精度,提示该流程可标准化术前计划转移。
要点
- 3D打印圆柱模板辅助PMEG开窗定位,台架验证精度高。
- 中位弧长偏差0.3 mm,高度偏差0.2 mm。
- 树脂类型、打印顺序和靶血管未一致影响定位精度。
核心结论
- 3D打印圆柱模板在PMEG中可促进开窗精准可靠定位。
- 当前工作流程可提供可重复工具以标准化术前计划向移植物转移。
研究设计与样本
- 台架验证研究,使用5例CT血管造影脚本化设计CAD模板。
- 模板标准化几何:高100 mm、直径30 mm、壁厚4 mm、腹腔干距顶部20 mm、开窗直径6 mm,12点钟参考。
- 模板切片后使用BioMed Amber、BioMed Clear和Dental树脂在桌面立体光刻打印机打印。
- 共评估54个打印开窗,比较测量与计划开窗中心的弧长偏差和高度偏差。
主要发现
- 54个打印开窗中,中位弧长偏差0.3 mm(IQR 0.2-0.5),中位高度偏差0.2 mm(IQR 0.2-0.3)。
- 按树脂类型,中位弧长偏差:Dental 0.3 mm(IQR 0.1-0.6)、Amber 0.3 mm(IQR 0.2-0.6)、BioMed Clear 0.3 mm(IQR 0.2-0.5)。
- 按树脂类型,高度偏差:Dental 0.2 mm(IQR 0.1-0.3)、Amber 0.2 mm(IQR 0.1-0.2)、Clear 0.3 mm(IQR 0.2-0.3)。
- 开窗打印顺序或靶血管未导致定位一致性退化或改善。
临床怎么用
- 在PMEG台面准备中,可使用3D打印圆柱模板按标准化工作流程转移术前开窗计划。
- 高精度和可重复性有助于减少因位置偏差导致的对位不良、导管操作时间延长及靶血管不稳定。
局限性
- 研究为台架验证,非临床结局评估。
- 样本量有限:5例CT血管造影、54个开窗。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
OBJECTIVE: To describe and bench-validate a shareable, version-locked computer-aided design (CAD) to 3-dimensional (3D)-print workflow that generates a cylindrical template to guide fenestration placement during preparation of physician-modified endografts (PMEGs). METHODS: Five computed tomographic angiograms were used to script a CAD template in Onshape with standardized geometry (height 100 mm, diameter 30 mm, wall 4 mm, celiac 20 mm from the top, fenestration diameter 6 mm) and a 12-o'clock reference. Templates were sliced in PreForm v3.5.1 and printed on a desktop stereolithography printer using BioMed Amber, BioMed Clear, and Dental resins. Accuracy was assessed on bench models by comparing measured versus planned fenestration centers, expressed as arc-length bias (mm along the circumference) and height bias (mm along the longitudinal axis). Secondary analysis examined the impact of resin type, fenestration print order (first-fourth), and target vessel. RESULTS: Across 54 printed fenestrations, median arc-length bias and height bias were 0.3 mm (interquartile range [IQR] 0.2-0.5) and 0.2 mm (IQR 0.2-0.3), respectively. Median arc-length bias by resin type was as follows: Dental 0.3 mm (IQR 0.1-0.6), Amber 0.3 mm (IQR 0.2-0.6), and BioMed Clear 0.3 mm (IQR 0.2-0.5). The height bias for Dental, Amber, and Clear resins was 0.2 mm (IQR 0.1-0.3), 0.2 mm (IQR 0.1-0.2), and 0.3 mm (IQR 0.2-0.3), respectively. There was no consistent degradation or improvement for the fenestration positioning depending on the sequence in which fenestrations were created during the printing for a specific template, or by target vessel. CONCLUSION: Using a 3D-printed cylindrical template during PMEGs holds potential to facilitate precise, reliable positioning of fenestrations on the endograft. The current workflow could provide a reproducible tool to standardize back-table transfer of the preoperative plan for PMEGs.Clinical ImpactPhysician-modified endograft remains a valuable option for endovascular treatment of complex abdominal aortic aneurysms, particularly given the limited availability of custom-made devices in some centers, their high cost, and prolonged manufacturing times. Although clinical outcomes of PMEGs have been promising, standardization across centers remains limited. From a clinical perspective, high accuracy and reproducibility are essential, as positional deviations may compromise alignment, potentially leading to prolonged catheterization times and target vessel instability. The use of a 3D-printed model within a standardized workflow, such as the one described in the present study, may facilitate reliable and reproducible transfer of the preoperative plan onto the endograft.
引用
- Huistra EWM, Strauss B, Pitcher GS, et al. Validation of a 3D-Printed Template for Fenestrations in Physician-Modified Endografts. J Endovasc Ther. 2026. PMID: 42473162. doi:10.1177/15266028261467291
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。