文献速递外周动脉疾病

定制3D打印模型用于外周动脉疾病血管内治疗术前规划与模拟:单盲随机对照试验

Custom Made Three Dimensional Printed Models for Pre-operative Planning and Simulation of Endovascular Treatment of Peripheral Artery Disease (3DPAD-1): A Single Blind Randomised Controlled Trial.
PubMed 文献 · Eur J Vasc Endovasc Surg · 2026-06-19

该单中心单盲随机对照试验纳入106例拟行主髂-股腘动脉外周动脉疾病血管内治疗的患者,1:1随机分为标准CT血管造影规划组和CT血管造影联合定制3D打印模型规划与模拟组。

要点

  • 3D打印模型规划使围术期并发症累积发生率从49.0%降至20.8%。
  • 3D打印模型规划使手术时间平均缩短40.3分钟。
  • 技术成功、造影剂用量、辐射暴露等指标无显著组间差异。

核心结论

  • 定制3D打印模型可显著降低外周动脉疾病血管内治疗的围术期并发症并缩短手术时间。
  • 研究结果支持在复杂血管内干预中选择性采用3D打印模型以提高手术效率和患者安全。

研究设计与样本

  • 单中心、单盲随机对照试验(3DPAD-1),注册号NCT07000097。
  • 2022年1月至2024年9月连续纳入拟行血管内治疗的主髂-股腘动脉外周动脉疾病患者。
  • 筛查166例,随机106例(每组53例),99例接受分配干预(3D模型组48例,标准组51例)。
  • 随机1:1分为标准CT血管造影规划组和CT血管造影联合3D打印模型规划与模拟组。

临床怎么用

  • 对于复杂主髂-股腘动脉外周动脉疾病血管内治疗,可考虑术前采用定制3D打印模型进行规划和模拟。
  • 3D打印模型规划有助于降低围术期并发症风险并提高手术效率。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

OBJECTIVE: This trial aimed to assess whether custom made three dimensional (3D) printed vascular models improve procedural outcomes when used for pre-operative planning and simulation in endovascular treatment (EVT) of aorto-iliac-femoropopliteal peripheral artery disease (PAD). METHODS: This single centre, single blind randomised controlled trial (3DPAD-1), registered on ClinicalTrials.gov (Identifier: NCT07000097), enrolled consecutive patients scheduled for EVT between January 2022 and September 2024. Participants were randomised 1 : 1 to standard planning based on computed tomography angiography (CTA) alone (standard group, SG) or CTA plus 3D printed model based planning and simulation (3D model group, 3DMG). The pre-specified coprimary endpoints were the cumulative 30 day incidence of peri-operative complications and total procedure duration. Secondary endpoints included technical success, contrast medium volume, radiation exposure, fluoroscopy time, and number of devices used. RESULTS: Of 166 patients screened, 106 were randomised (53 per arm); 99 underwent the allocated intervention (48 in the 3DMG, 51 in the SG). The cumulative incidence of complications was significantly lower in the 3DMG (20.8%) than in the SG (49.0%; p = .006). The univariable logistic model (OR 0.27, 95% CI 0.11 - 0.66; p = .004), the multivariable model (adjusted OR 0.22, 95% CI 0.08 - 0.60; p = .004), and the propensity weighted analyses (Average Treatment Effect OR 0.33, 95% CI 0.13 - 0.86; p = .023; Average Treatment Effect in the Overlap Population OR 0.35, 95% CI 0.14 - 0.79; p = .023) consistently confirmed the protective effect of the 3D model. Procedure duration was significantly shorter in the 3DMG (mean difference -40.3 minutes; p < .001), confirmed in adjusted and weighted models. No significant between group differences were observed in other peri-operative outcomes. CONCLUSION: Custom made 3D printed models significantly reduced peri-operative complications and procedure duration in EVT for PAD, supporting their role in improving procedure planning and efficiency. These findings support the selective adoption of 3D printed models for complex endovascular interventions to enhance procedure efficiency and patient safety.

来源:Eur J Vasc Endovasc Surg,查看原文。版权归原作者所有。

引用

  1. Perini P, Martini C, Bianchini Massoni C, et al. Custom Made Three Dimensional Printed Models for Pre-operative Planning and Simulation of Endovascular Treatment of Peripheral Artery Disease (3DPAD-1): A Single Blind Randomised Controlled Trial. Eur J Vasc Endovasc Surg. 2026. PMID: 42314902. doi:10.1016/j.ejvs.2026.06.035

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。