文献速递主动脉疾病内脏/肾动脉与血管畸形

分叉支架内原位技术:单分支定向构建双靶血管桥接支架系统的2例报告

Bifurcated In-Stent in Situ Technique for Creation of a Bifurcated Bridging Stent-Graft System to 2 Target Vessels Using a Single Directional Branch: A Report of 2 Cases.
PubMed 文献 · J Endovasc Ther · 2025-10-26

本文描述了一种新型分叉支架内原位技术(BIS2T),利用单分支定向构建分叉桥接支架系统以纳入2根靶血管,用于复杂主动脉瘤腔内修复。技术使用3枚球囊扩张式支架移植物,通过原位开窗和对接技术完成分叉。2例患者接受治疗,均无并发症或内漏,随访CTA显示分支通畅。结论认为该技术可行,可为解剖条件复杂的患者提供腔内治疗选择。

要点

  • BIS2T技术利用单分支定向通过原位开窗和对接构建分叉支架系统,纳入2根靶血管。
  • 2例患者治疗后无并发症和内漏,随访CTA显示分支通畅。
  • 该技术可能为靶血管解剖复杂、常规技术难以纳入的患者提供腔内治疗机会。

核心结论

  • BIS2T是利用单分支定向构建分叉桥接支架系统以纳入2根靶血管的可行选项。

研究设计与样本

  • 技术报告类研究,描述BIS2T的操作技术并报告2例患者的治疗结果。

主要发现

  • 2例患者接受BIS2T治疗,均未发生并发症或内漏。
  • 随访CTA显示2例患者的分支均保持通畅。

关键数值与推荐

  • 技术使用3枚球囊扩张式支架移植物。
  • 第一枚支撑支架从定向分支部署至第一靶血管或动脉瘤囊。
  • 使用再入导管在第一支架上创建原位开窗,先用3 mm 0.014英寸血管成形球囊预扩张。
  • 第二枚支架部署至第二靶血管,与第一支架重叠>1 cm。
  • 第三枚匹配支架以对吻支架方式加固分叉,形成「D形」支架构型。

临床怎么用

  • 对于靶血管解剖复杂(如变异或副血管、腹腔干肠系膜上动脉共干、动脉瘤/夹层延伸至靶血管)而不适合标准腔内技术纳入的患者,可考虑BIS2T。
  • 该技术可能避免 intentional artery coverage 或使原本不适合腔内治疗的病例获得治疗机会。

局限性

  • 仅报告2例患者,样本量小,缺乏长期随访数据。
  • 技术复杂性高,需要特定的器械和操作经验。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

OBJECTIVE: The objective of the study is to describe a novel bifurcated in-stent in situ technique (BIS2T) for creation of a bifurcated bridging stent-graft system to target 2 vessels using a single directional branch during complex endovascular aortic aneurysm. TECHNIQUE: The technique uses 3 balloon-expandable stent-grafts. The first supporting stent-graft is deployed from the directional branch into the first target vessel or aneurysm sac. A reentry catheter is used to create an in situ fenestration in the first stent-graft, which is predilatated with a 3 mm 0.014 inch angioplasty balloon. This is exchanged for a 0.035 inch 5 Fr catheter and guidewire which is used for catheterization of the second target vessel via the in situ fenestration. The docking area of the first stent-graft is predilated. The second stent-graft is deployed into the second target with >1 cm overlap into the first stent-graft, followed by a matching third stent-graft in a kissing stent fashion to reinforce the bifurcation and achieve a "D shape" stent-graft configuration. RESULTS: The BIS2T was used to treat 2 patients. Neither experienced complications or endoleaks, and both had patent branches on follow-up computed tomography angiography. CONCLUSIONS: The BIS2T is a feasible option to incorporate 2 target vessels via a single directional branch.Clinical ImpactTarget vessel anatomy is a frequent limitation for successful endovascular incorporation using fenestrations or directional branches during complex endovascular aortic aneurysm repair. Numerous anatomical variations such as aberrant or accessory vessels, common celio-mesenteric trunks, or extension of the aneurysm/dissection into a target vessel may preclude successful incorporation using standard endovascular techniques. This technical note describes a novel bifurcated in-stent in situ technique (BIS2T) for the creation of a bifurcated bridging stent-graft system to target 2 vessels using a single directional branch. This approach may enable target vessel incorporation in challenging anatomical situations that might otherwise preclude endovascular treatment or require intentional artery coverage.

来源:J Endovasc Ther,查看原文。版权归原作者所有。

引用

  1. Paludetto G, Mesquita L, Pagnin Schmid B, et al. Bifurcated In-Stent in Situ Technique for Creation of a Bifurcated Bridging Stent-Graft System to 2 Target Vessels Using a Single Directional Branch: A Report of 2 Cases. J Endovasc Ther. 2025. PMID: 41139824. doi:10.1177/15266028251384906

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。