文献速递泌尿系结石

用于输尿管镜术中测量肾盂内压的解剖体外肾脏模型的开发与测试

Development and Testing of an Anatomic in vitro Kidney Model for Measuring Intrapelvic Pressure During Ureteroscopy.
PubMed 文献 · Urology · 2021-05-05

研究开发了一种硅胶肾脏体外模型,可模拟输尿管镜术中的肾盂内压(IPP),并通过调节阀门模拟输尿管流出。在无输尿管通道鞘(UAS)条件下,IPP随灌注压升高而增加,当灌注压≥153cmH2O时超过40cmH2O;使用UAS时所有灌注压下IPP均低于40cmH2O。该模型与既往体内和离体数据相符,可用于测试新技术对IPP的影响。

要点

  • 体外硅胶肾脏模型可模拟输尿管镜术中的肾盂内压。
  • 无UAS时,灌注压≥153cmH2O导致IPP超过40cmH2O。
  • 使用UAS时,所有测试灌注压下IPP均低于40cmH2O。

核心结论

  • 体外肾脏模型能模拟体内和离体的IPP变化,并可通过控制液体流出模拟不同条件。

研究设计与样本

  • 研究采用硅胶肾脏模型(Simagine Health),配备0.2 mm压力传感器(Opsens)和Tuohy-Borst阀,用Cobra输尿管镜(Wolf)在200cmH2O灌注下校准至IPP 54cmH2O。
  • 实验在工作通道置入激光纤维,使用或不使用UAS(11/13F、13/15F),灌注压设为61、102、153、193cmH2O,用自动系统(Rocamed)测量稳态IPP。

主要发现

  • 无UAS条件下,IPP随灌注压升高而增加,当灌注压≥153cmH2O时IPP超过40cmH2O。
  • 使用UAS时,所有灌注压下IPP均低于40cmH2O。
  • 各条件下IPP值与既往体内和离体模型数据相符。

关键数值与推荐

  • 校准目标IPP为54cmH2O(基于既往人体数据)。
  • UAS规格为11/13F和13/15F,灌注压设置为61、102、153、193cmH2O。
  • IPP阈值40cmH2O用于评估安全性。

临床怎么用

  • 该模型可用于测试新器械和技术对IPP的影响。
  • 使用UAS有助于在较高灌注压下维持IPP低于40cmH2O。

局限性

  • 原文未报告局限性。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

OBJECTIVES: To create an in vitro anatomic bench model that can mimic in vivo intrapelvic pressure (IPP) during ureteroscopy (URS) and compare it against existing in vivo and ex vivo data. METHODS: A silicone kidney model (Simagine Health) that permits intrarenal endoscopic navigation was engineered to have a fluid-tight seal for the ureteral opening and a Tuohy-Borst valve in the renal pelvis incorporating a 0.2 mm pressure sensor (Opsens). To calibrate the model, a Cobra ureteroscope (Wolf) was inserted to the pelvis with 200cmH2O irrigation, and the valve adjusted until an IPP of 54cmH2O was obtained (prior human data). All experiments were conducted with a laser fiber in the working channel, with and without ureteral access sheaths (UAS) (11/13F, 13/15F) at irrigation setting of 61, 102, 153, and 193cmH2O using an automated system (Rocamed). Study outcome was mean steady-state IPP for each UAS/irrigation condition. RESULTS: Fluid leakage through the Tuohy-Borst valve, which could be adjusted, was critical to simulate ureteric outflow during URS. IPP values for each condition corresponded with data from in vivo and ex vivo models. In the no UAS condition, IPP increased with increasing irrigation pressures, and surpassed 40cmH2O when ≥153cmH2O. When using a UAS, IPP was below 40cmH2O for all irrigation pressures. CONCLUSIONS: An in vitro kidney model can simulate in vivo and ex vivo IPP profiles, and be tailored to different conditions by controlling fluid outflow. This bench model can be useful for testing of new technologies and their impact on IPP.

来源:Urology,查看原文。版权归原作者所有。

引用

  1. Patel AU, Aldoukhi AH, Majdalany SE, et al. Development and Testing of an Anatomic in vitro Kidney Model for Measuring Intrapelvic Pressure During Ureteroscopy. Urology. 2021. PMID: 33961891. doi:10.1016/j.urology.2021.04.024

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。