个体化3D打印透明肾脏模型辅助机器人辅助肾部分切除术治疗复杂肾肿瘤的前瞻性配对研究
这项前瞻性配对研究纳入80例接受机器人辅助肾部分切除术(RPN)的复杂肾肿瘤患者(R.E.N.A.L.评分≥7),比较术中应用个体化3D打印透明肾脏模型(40例)与常规方案(40例)的效果。结果显示模型组控制台时间较匹配组减少约20%(64.6 vs 78.5分钟,P=0.001),多因素分析中肿瘤半径(P<0.001)和模型应用(P=0.009)是控制台时间≤70分钟的显著预测因素。
要点
- 3D打印透明肾脏模型可减少复杂肾肿瘤RPN的控制台时间约20%。
- 肿瘤半径和模型应用是控制台时间≤70分钟的独立预测因素。
- 模型应用有望拓宽肾部分切除术的适应证。
核心结论
- 个体化3D打印透明肾脏模型有助于更有效地实施机器人辅助肾部分切除术,即使对复杂肾肿瘤也能缩短手术时间。
研究设计与样本
- 前瞻性病例配对研究,纳入80例接受RPN的复杂肾肿瘤患者(R.E.N.A.L.评分≥7),模型组40例术中使用3D打印透明肾脏模型,匹配组40例采用常规方案,均由同一名经验丰富的外科医生完成手术。
主要发现
- 模型组控制台时间较匹配组减少约20%(64.6 vs 78.5分钟,P=0.001)。
- 多因素logistic回归分析显示肿瘤半径(P<0.001)和模型应用(P=0.009)是控制台时间≤70分钟的显著预测因素。
临床怎么用
- 对于R.E.N.A.L.评分≥7的复杂肾肿瘤,在RPN术中使用个体化3D打印透明肾脏模型可能缩短控制台时间并有助于拓宽肾部分切除术的适应证。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
OBJECTIVES: To evaluate the effectiveness of a three-dimensional (3D) printed transparent kidney model as a surgical navigator for robot-assisted partial nephrectomy (RPN) in patients with complex renal tumours, defined by a R.E.N.A.L. (Radius, Exophytic/Endophytic, Nearness, Anterior/Posterior, Location) nephrometry score of ≥7. PATIENTS AND METHODS: A total of 80 patients who underwent RPN were included in the present prospective case-matched study (case group [n = 40, application of 3D-printed transparent kidney model during RPN] vs matching group [n = 40, routine protocol]). The RPNs were performed by a single experienced surgeon. The RPN procedure consisted of six steps: (i) preparation of the renal hilar vessel for clamping, (ii) tumour detection and dissection, (iii) robotic ultrasonography, (iv) tumour resection, (v) calyx repair and haemostasis, and (vi) renorrhaphy. The time for each step, console time, and warm ischaemia time were compared between the two groups as a surrogate marker for surgical effectiveness. RESULTS: Both groups were well-balanced for all baseline characteristics. The use of the model reduced the console time by ~20% compared to the matched group (64.6 vs 78.5 min, P = 0.001). On multivariate logistic regression analysis, tumour radius (P < 0.001) and application of the model (P = 0.009) were identified as significant predictors of a console time of ≤70 min. CONCLUSION: We established the usefulness of a personalised 3D-printed transparent kidney model for more effective RPNs. Use of the 3D-printed transparent kidney model reduced the operative time even for complex renal tumours and would be expected to broaden the indications for PN.
引用
- Kwon Kim J, Ryu H, Kim M, et al. Personalised three-dimensional printed transparent kidney model for robot-assisted partial nephrectomy in patients with complex renal tumours (R.E.N.A.L. nephrometry score ≥7): a prospective case-matched study. BJU Int. 2020. PMID: 33064867. doi:10.1111/bju.15275
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。