文献速递前列腺癌

基于三维磁共振成像打印的前列腺解剖及靶向活检证实索引肿瘤模型辅助个体化根治性前列腺切除术的可行性研究

Three-dimensional Magnetic Resonance Imaging-based Printed Models of Prostate Anatomy and Targeted Biopsy-proven Index Tumor to Facilitate Patient-tailored Radical Prostatectomy-A Feasibility Study.
PubMed 文献 · Eur Urol Oncol · 2020-08-29

采用PI-RADS v2.0的36区方案比较MRI/三维打印与全mount病理,结果显示索引病灶定位均正确,显著前列腺癌病灶定位显著相关(Pearson相关系数0.88;p<0.001),肿瘤及前列腺宽度、长度、体积与病理显著相关。

要点

  • 三维打印前列腺模型与最终病理对显著肿瘤病灶定位显著相关(r=0.88;p<0.001)。
  • 模型与病理在肿瘤及前列腺宽度、长度、体积上显示显著相关。

核心结论

  • 基于术前MRI的三维打印前列腺模型与最终病理相关性良好,可用于个体化规划根治性前列腺切除术。

主要发现

  • 所有病例中索引病灶定位均由MRI和三维模型正确显示。
  • 显著前列腺癌病灶定位显著相关(Pearson相关系数0.88;p<0.001)。
  • 三维打印模型与病理衍生的肿瘤及前列腺宽度、长度、体积显示显著相关(Pearson相关分析及Bland-Altman图)。

关键数值与推荐

  • 采用36区PI-RADS v2.0方案比较MRI/三维打印与全mount病理。

临床怎么用

  • 三维打印前列腺模型可辅助根治性前列腺切除术的个体化规划及术中冰冻切片决策。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

In this prospective single-center feasibility study, we demonstrate that the use of three-dimensional (3D)-printed prostate models support nerve-sparing radical prostatectomy (RP) and intraoperative frozen sectioning (IFS) in ten men suffering from intermediate- and high-risk prostate cancer (PC), of whom seven harbored pT3 disease. Patient-specific 3D resin models were printed based on preoperative multiparametric magnetic resonance imaging (mpMRI) to provide an exact 3D impression of significant tumor lesions. RP and IFS were planned in a patient-tailored fashion. The 36-region Prostate Imaging Reporting and Data System (PI-RADS) v2.0 scheme was used to compare the MRI/3D print with whole-mount histopathology. In all cases, localization of the index lesion was correctly displayed by MRI and the 3D model. Localization of significant PC lesions correlated significantly (Pearson`s correlation coefficient of 0.88; p < 0.001). In addition, a significant correlation of the width, length, and volume of the tumor and prostate gland, derived from the printed model and histopathology, was found, using Pearson's correlation analyses and Bland-Altman plots. In conclusion, 3D-printed prostate models correlate well with final pathology and can be used to tailor RP. PATIENT SUMMARY: The use of three-dimensional (3D)-printed prostate models based on preoperative magnetic resonance imaging (MRI) may improve prostatectomy outcome. This study confirmed the accuracy of 3D-printed prostates compared with pathology from radical prostatectomy specimens. Thus, MRI-derived 3D-printed prostate models can assist in prostate cancer surgery.

来源:Eur Urol Oncol,查看原文。版权归原作者所有。

引用

  1. Darr C, Finis F, Wiesenfarth M, et al. Three-dimensional Magnetic Resonance Imaging-based Printed Models of Prostate Anatomy and Targeted Biopsy-proven Index Tumor to Facilitate Patient-tailored Radical Prostatectomy-A Feasibility Study. Eur Urol Oncol. 2020. PMID: 32873530. doi:10.1016/j.euo.2020.08.004

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。