文献速递前列腺癌

3D打印模型用于机器人辅助前列腺切除术中阳性手术切缘的切除

3D-printed model for resection of positive surgical margins in robot-assisted prostatectomy.
PubMed 文献 · BJU Int · 2024-11-27

这项前瞻性多中心队列研究纳入100例2018年9月至2021年8月间接受神经保留机器人辅助根治性前列腺切除术的患者,利用基于盆腔磁共振成像制作的三维打印前列腺模型标记冰冻切片发现的阳性切缘并指导术中二次切除。冰冻切片发现23%的病例存在阳性切缘,模型指导的二次切除使83%(19/23例)转为阴性切缘;二次切除标本肿瘤检出率为39%(9/23例)。作者认为将三维打印前列腺模型整合入神经保留机器人辅助根治性前列腺切除术可能通过提高二次切除精确性改善手术结局。

要点

  • 冰冻切片发现23%病例存在阳性切缘,模型指导二次切除后83%(19/23例)转为阴性切缘。
  • 二次切除标本肿瘤检出率为39%(9/23例)。
  • 19例切缘转阴患者中18例(95%)术后2个月前列腺特异性抗原不可测,6例(32%)12个月内生化复发。

核心结论

  • 将三维打印前列腺模型整合入神经保留机器人辅助根治性前列腺切除术可能通过提高二次切除精确性和优化病理-手术沟通对手术结局产生积极影响。

研究设计与样本

  • 前瞻性多中心队列研究,纳入2018年9月至2021年8月间接受神经保留机器人辅助根治性前列腺切除术的100例患者。
  • 三维打印前列腺模型基于盆腔磁共振成像制作,用于标记阳性手术切缘并指导术中二次切除。
  • 主要终点为冰冻切片识别的阳性切缘转为无肿瘤切缘的转化率,次要终点为12个月随访内的功能与肿瘤学参数。

主要发现

  • 冰冻切片期间23%的病例发现阳性切缘,模型指导的二次切除使83%(19/23例)转为阴性手术切缘。
  • 二次切除标本的肿瘤检出率为39%(9/23例)。
  • 19例切缘转阴患者中,18例(95%)术后2个月前列腺特异性抗原不可测,6例(32%)在12个月内出现后续生化复发。
  • 前列腺特异性膜抗原正电子发射断层扫描计算机断层扫描发现1例局部复发和5例转移性疾病。
  • 切缘转阴患者中,基线国际勃起功能指数五项版本评分中位数在1年后下降16%,与原发性阴性切缘患者相比无显著差异。

临床怎么用

  • 原文未据此给出推荐。

局限性

  • 缺乏对照组。
  • 冰冻切片结果可能存在假阴性。
  • 磁共振成像准确性有限。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

OBJECTIVES: To improve precision of secondary resection (SR) after positive surgical margin (PSM) detection by frozen section (FS) during nerve-sparing (NS) robot-assisted radical prostatectomy (RARP) by employing a personalised three-dimensional (3D)-printed prostate model derived from pelvic magnetic resonance imaging (MRI). This model was used to mark positive surgical margins (PSM) and guide intraoperative SR during NS-RARP. PATIENTS AND METHODS: Prospective multicentre cohort study with 100 patients undergoing NS-RARP between September 2018 and August 2021. Primary and secondary endpoints were the conversion rate of FS-identified PSM to a tumour-free margin and functional/oncological parameters within a 12-month follow-up, respectively. RESULTS: A PSM was identified in 23% of cases during FS, with a conversion to negative surgical margins (NSM) in 83% (19/23 cases) by model-guided SR. The tumour detection rate in SR specimens was 39% (nine of 23 cases). Among the 19 patients with converted margins, 18 (95%) achieved undetectable prostate-specific antigen levels 2 months postoperatively, with six (32%) having subsequent biochemical recurrence within 12 months. prostate-specific-membrane-antigen positron emission tomography computed tomography found one local recurrence, and five cases of metastatic disease. In converted patients, the baseline median five-item version of the International Index of Erectile Function score decreased by 16% after 1 year, with no significant difference compared to patients with primarily NSM. Limitations include the absence of a control group, the potential for false-negative FS results and limited accuracy of MRI. CONCLUSION: The integration of 3D-printed prostate models into NS-RARP has the potential to positively impact surgical outcomes by improving the precision of SR and optimising pathosurgical communication.

来源:BJU Int,查看原文。版权归原作者所有。

引用

  1. Engesser C, Brantner P, Gahl B, et al. 3D-printed model for resection of positive surgical margins in robot-assisted prostatectomy. BJU Int. 2024. PMID: 39601472. doi:10.1111/bju.16595

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。