文献速递流行病学与生物统计临床试验与 GCP

当存在 Pipeline 数据时,针对重复测量设计的成组序贯试验的设计与分析:教程

Design and Analysis of Group Sequential Trials for Repeated Measurements When Pipeline Data Occurs: A Tutorial.
PubMed 文献 · Stat Med · 2025-01-01

本教程针对主要终点延迟测量且需重复测量的成组序贯试验,阐述了如何在计划阶段考虑 pipeline 受试者(已入组但最终终点尚未观测)的早期测量数据,以及如何在期中分析决定停止入组后,将这些受试者后续贡献的数据正式纳入最终分析,并扩展了现有方法(如添加无效性非约束性停止规则、推导有效 p 值和置信区间的计算细节),同时提供 R 包和 R 代码。

要点

  • 成组序贯试验允许因有效性或无效性提前终止而不损害其有效性。
  • 对于延迟测量的终点,期中分析时可能存在 pipeline 受试者,其早期测量数据可用于提高统计功效。
  • 期中分析决定停止入组后,pipeline 患者仍会贡献额外数据,理想做法是以正式方式纳入最终分析。

核心结论

  • 本教程为具有重复测量和延迟终点的成组序贯试验提供了规划与分析指导,包括如何正式纳入 pipeline 数据,并扩展了现有方法(如添加无效性非约束性停止规则、推导有效 p 值和置信区间的计算细节),同时提供 R 包和 R 代码。

研究设计与样本

  • 本文为教程论文,讨论成组序贯试验在终点延迟测量且需重复测量时的设计、规划与分析方法,并扩展现有方法,提供 R 包和 R 代码。

主要发现

  • 考虑 pipeline 受试者的早期测量已被证明可提高统计功效。
  • 期中分析决定停止入组后,pipeline 患者仍会贡献额外数据,理想做法是以正式方式纳入最终分析。
  • 教程扩展了现有方法,例如添加无效性非约束性停止规则,并推导有效 p 值和置信区间的计算细节。

局限性

  • 原文未报告局限性

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

Group sequential trials (GST) allow for early stopping of a clinical trial for efficacy or futility, without compromising its validity. Statistical methodology for GST is well established when the endpoint is observed immediately, but less so for endpoints that are measured with a delay, such as repeatedly measured outcomes for which the primary measurement of interest is taken after several months. The latter can result in pipeline subjects at an interim analysis. These subjects may have early outcome measurements available, but their final endpoint is yet to be observed. Accounting for these early measurements has been shown to increase statistical power. Most importantly, pipeline patients will contribute with additional data after a decision to stop enrollment has been taken at an interim analysis. To make the best use of all available data, these data are ideally incorporated in the final analysis in a formal way. In this tutorial paper, we provide guidance on how to plan a GST with repeated measurements and a delayed endpoint and how to analyze the data resulting from these trials. We discuss existing methods, and also expand on them, for example adding a nonbinding stopping rule for futility and working out the computational details to derive valid p-values and confidence intervals. We also provide an R package and R code to perform the methods discussed in this paper.

来源:Stat Med,查看原文。版权归原作者所有。

引用

  1. Baayen C, Blanche P, Jennison C, et al. Design and Analysis of Group Sequential Trials for Repeated Measurements When Pipeline Data Occurs: A Tutorial. Stat Med. 2025. PMID: 40514767. doi:10.1002/sim.70130

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。