3D打印肌电手部矫形器用于脊髓损伤患者手功能康复
本研究开发了一种由肌电信号控制的3D打印手部矫形器,旨在辅助颈段脊髓损伤患者抓握。
要点
- 3D打印肌电手部矫形器可改善慢性颈段脊髓损伤患者的手功能(TRI-HFT,p < 0.05)。
- 佩戴矫形器后受试者即刻获得进食功能,多数对设备满意。
- 研究未报告与实验相关的不良反应。
核心结论
- 3D打印肌电手部矫形器直观、易用,对处理日常生活物品有积极效果。
- 将简单肌电控制策略与3D打印技术结合在康复工程中是可行且有前景的。
研究设计与样本
- 使用计算机辅助设计软件设计三维结构,以聚乳酸线材打印。
- 采用肌电信号均方根作为设备控制输入。
- 主要结局指标为Toronto Rehabilitation Institute手功能测试(TRI-HFT)。
- 同时评估日常生活功能独立性改善和设备可用性。
主要发现
- 佩戴矫形器后TRI-HFT评分改善,p < 0.05。
- 受试者佩戴后即刻获得进食功能。
- 多数受试者对设备满意(可用性测试)。
- 未报告与实验相关的不良反应。
关键数值与推荐
- TRI-HFT用于评估佩戴矫形器前后的手功能,改善具有统计学意义(p < 0.05)。
- 设备通过增强腱固定抓握提供足够的抓握功能。
- 肌电信号均方根作为控制设备的输入。
临床怎么用
- 该3D打印肌电手部矫形器可用于辅助慢性颈段脊髓损伤患者抓握和进食。
- 设备设计为低成本个性化,适合康复工程应用。
局限性
- 试验为回顾性注册(KCT0003995,2019年5月2日)。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
BACKGROUND: Spinal cord injury (SCI) is a severe medical condition affecting the hand and locomotor function. New medical technologies, including various wearable devices, as well as rehabilitation treatments are being developed to enhance hand function in patients with SCI. As three-dimensional (3D) printing has the advantage of being able to produce low-cost personalized devices, there is a growing appeal to apply this technology to rehabilitation equipment in conjunction with scientific advances. In this study, we proposed a novel 3D-printed hand orthosis that is controlled by electromyography (EMG) signals. The orthosis was designed to aid the grasping function for patients with cervical SCI. We applied this hand exoskeleton system to individuals with tetraplegia due to SCI and validated its effectiveness. METHODS: The 3D architecture of the device was designed using computer-aided design software and printed with a polylactic acid filament. The dynamic hand orthosis enhanced the tenodesis grip to provide sufficient grasping function. The root mean square of the EMG signal was used as the input for controlling the device. Ten subjects with hand weakness due to chronic cervical SCI were enrolled in this study, and their hand function was assessed before and after wearing the orthosis. The Toronto Rehabilitation Institute Hand Function Test (TRI-HFT) was used as the primary outcome measure. Furthermore, improvements in functional independence in daily living and device usability were evaluated. RESULTS: The newly developed orthosis improved hand function of subjects, as determined using the TRI-HFT (p < 0.05). Furthermore, participants obtained immediate functionality on eating after wearing the orthosis. Moreover, most participants were satisfied with the device as determined by the usability test. There were no side effects associated with the experiment. CONCLUSIONS: The 3D-printed myoelectric hand orthosis was intuitive, easy to use, and showed positive effects in its ability to handle objects encountered in daily life. This study proved that combining simple EMG-based control strategies and 3D printing techniques was feasible and promising in rehabilitation engineering. TRIAL REGISTRATION: Clinical Research Information Service (CRiS), Republic of Korea. KCT0003995. Registered 2 May 2019 - Retrospectively registered.
引用
- Yoo HJ, Lee S, Kim J, et al. Development of 3D-printed myoelectric hand orthosis for patients with spinal cord injury. J Neuroeng Rehabil. 2019. PMID: 31888695. doi:10.1186/s12984-019-0633-6
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。