乳头工程:用外部支架处理自体肋软骨维持乳头几何形态
本研究提出将术中废弃的自体肋软骨经切碎或刨碎处理后装入3D打印PLA外部支架,植入裸鼠3个月后评估。结果显示支架组乳头轮廓、凸度和体积保持显著更优,处理后软骨的平衡模量更接近人乳头组织,组织学见健康活软骨伴纤维血管组织长入。
要点
- 切碎或刨碎的自体肋软骨装入3D打印PLA支架可维持乳头轮廓与凸度。
- 处理后软骨的平衡模量更接近天然人乳头组织。
- 植入3个月后支架内仍见健康活软骨并被纤维血管组织包绕。
核心结论
- 自体肋软骨可术中处理并置入生物相容性外部支架,以模拟天然人乳头的形状和生物力学特性。
研究设计与样本
- 动物实验研究:设计并3D打印PLA外部支架,将患者来源肋软骨切碎或刨碎后装入支架,植入裸鼠,3个月后取出进行体积、组织学和生物力学分析,并与天然人乳头组织及未处理肋软骨对照。
主要发现
- 植入3个月后大体分析显示支架组乳头轮廓、凸度和体积保持显著更优。
- 力学分析显示处理后的软骨植入物平衡模量值更接近人乳头组织。
- 组织学分析显示植入3个月后仍有健康且有活力的软骨,并伴有纤维血管组织包绕。
临床怎么用
- 可利用乳房再造术中切除的自体肋软骨经处理装入3D打印外部支架,定制个体化工程化自体植入物以维持乳头凸度。
局限性
- 研究为裸鼠动物实验,样本量与统计细节原文未报告,人类临床适用性尚需进一步验证。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
INTRODUCTION: Nipple reconstruction is the essential last step of breast reconstruction after total mastectomy, resulting in improved general and aesthetic satisfaction. However, most techniques are limited by secondary scar contracture and loss of neo-nipple projection leading to patient dissatisfaction. Approximately, 16,000 patients undergo autologous flap breast reconstruction annually, during which the excised costal cartilage (CC) is discarded. We propose utilizing processed CC placed within biocompatible 3D-printed external scaffolds to generate tissue cylinders that mimic the shape, size and biomechanical properties of native human nipple tissue while mitigating contracture and projection loss. METHODS: External scaffolds were designed and then 3D-printed using polylactic acid (PLA). Patient-derived CC was processed by mincing or zesting, then packed into the scaffolds, implanted into nude rats and explanted after 3 months for volumetric, histologic and biomechanical analyses. Similar analyses were performed on native human nipple tissue and unprocessed CC. RESULTS: After 3 months in vivo, gross analysis demonstrated significantly greater preservation of contour, projection and volume of the scaffolded nipples. Mechanical analysis demonstrated that processing of the cartilage resulted in implant equilibrium modulus values closer to that of the human nipple. Histologic analysis showed the presence of healthy and viable cartilage after 3 months in vivo, invested with fibrovascular tissue. CONCLUSIONS: Autologous CC can be processed intraoperatively and placed within biocompatible external scaffolds to mimic the shape and biomechanical properties of the native human nipple. This allows for custom design and fabrication of individualized engineered autologous implants tailored to patient desire, without the loss of projection seen with traditional approaches.
引用
- Samadi A, Premaratne ID, Wright MA, et al. Nipple Engineering: Maintaining Nipple Geometry with Externally Scaffolded Processed Autologous Costal Cartilage. J Plast Reconstr Aesthet Surg. 2021. PMID: 33863678. doi:10.1016/j.bjps.2021.03.010
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。