新型显微外科机器人系统的临床前研究:硅胶血管吻合可行性与学习曲线
该临床前研究使用专为显微外科设计的MicroSure机器人系统原型,在硅胶血管上比较机器人辅助与传统显微吻合的效果。3名不同训练水平的操作者各完成10次手工吻合和10次机器人辅助吻合,由4名盲法评估的显微外科医生用改良SAMSS量表评分。结果显示机器人吻合可行,但耗时更长(35.1分钟对12.5分钟)、技能评分更低,但机器人辅助的学习曲线更陡峭。
要点
- 使用MicroSure机器人系统在硅胶血管上完成显微吻合是可行的
- 机器人辅助吻合时间35.1分钟,长于传统手工的12.5分钟
- 机器人辅助的SAMSS技能评分低于传统方法,但学习曲线更陡峭
核心结论
- 使用MicroSure机器人系统在硅胶血管上完成吻合性显微外科手术是可行的。
- 与传统方法相比,机器人辅助组吻合时间更长、显微外科技能质量更低。
- 机器人辅助在手术时间和显微外科技能各领域均表现出更陡峭的学习曲线。
研究设计与样本
- 临床前研究,3名不同显微外科训练水平的操作者参与。
- 每人完成10次手工吻合和10次机器人辅助吻合。
- 由4名盲法评估的经验丰富显微外科医生使用改良版显微外科技能结构化评估(SAMSS)评分。
- 记录吻合操作时间和不良事件。
主要发现
- 研究期间机器人辅助和手工吻合的总时间分别降至35.1分钟和12.5分钟。
- 传统方法SAMSS总体表现从2.8升至3.6,指示性技能从2.6升至3.7。
- 机器人辅助方法SAMSS总体表现从2.3升至3.0,指示性技能从2.3升至3.1。
临床怎么用
- 该机器人系统可用于硅胶血管模型的显微吻合训练与研究。
- 机器人辅助初期耗时更长、技能评分较低,但学习曲线更陡峭,提示随训练可改善。
- 结果支持进一步开发该系统并开展临床前及临床试验。
局限性
- 研究仅在硅胶血管模型上进行,非活体动物或临床环境。
- 样本量小,仅3名操作者参与。
- 使用原型系统,性能可能随系统迭代改变。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
BACKGROUND: Robotic assistance in microsurgery could enhance human precision and dexterity to improve clinical outcomes. Because no robotic device has been designed primarily for microsurgery, the authors developed a dedicated microsurgical robotic system. This preclinical study investigates whether microsurgical anastomosis can be successfully completed on silicone vessels using a prototype of this new robotic system, and compares outcomes of robot-assisted versus conventional microsurgery. METHODS: Three participants at different levels of microsurgical training completed 10 anastomoses by hand and 10 anastomoses with robotic assistance. Four blinded, experienced microsurgeons evaluated the quality of the microsurgical skills using a modified version of the Structured Assessment of Microsurgical Skills. Time to perform the anastomosis and adverse events were recorded. RESULTS: The total time to perform the anastomoses with and without robotic assistance decreased to 35.1 minutes and 12.5 minutes, respectively, during the study. The overall performance and indicative skill of the Structured Assessment of Microsurgical Skills improved with the conventional method (from 2.8 to 3.6 and from 2.6 to 3.7, respectively) and the robot-assisted method (from 2.3 to 3.0 and from 2.3 to 3.1, respectively). CONCLUSIONS: It is feasible to complete anastomotic microsurgery on silicone vessels using the MicroSure robotic system. In comparison with the conventional method, time to perform the anastomosis was longer and quality of microsurgical skills was lower in the robot-assisted group. However, the robot-assisted performance showed steeper learning curves for both surgical time and domains of microsurgical skills. The encouraging results indicate further development of the system and (pre)clinical trials.
引用
- van Mulken TJM, Boymans CAEM, Schols RM, et al. Preclinical Experience Using a New Robotic System Created for Microsurgery. Plast Reconstr Surg. 2018. PMID: 30119108. doi:10.1097/PRS.0000000000004939
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。