文献速递瘢痕与激光烧伤

3D打印透明面罩在面部瘢痕管理中的应用及其生物力学原理

The application of 3D-printed transparent facemask for facial scar management and its biomechanical rationale.
PubMed 文献 · Burns · 2017-10-09

该研究通过有限元分析建立3D打印透明面罩的生物力学模型,并招募10例6个月内面部深度烧伤患者进行临床研究,测量界面压力。治疗组5例在初始瘢痕评估后立即使用面罩,延迟治疗组5例在评估后1个月开始治疗,两组均在干预后1个月评估瘢痕。结果显示,经个体化设计调整和添加硅胶衬里优化压力后,全部10例患者瘢痕平均厚度和硬度在干预1个月后显著降低。

要点

  • 3D打印透明面罩设计及硅胶衬里对确保足够压缩压力至关重要
  • 全部10例患者干预1个月后瘢痕平均厚度和硬度显著降低
  • 延迟治疗组未干预的1个月内瘢痕平均厚度增加,干预后降低

核心结论

  • 面罩设计和硅胶衬里对于确保3D打印透明面罩提供足够的压缩压力很重要。
  • 使用3D打印透明面罩的干预似乎显示出控制面部增生性瘢痕厚度和硬度的效果。

研究设计与样本

  • 通过有限元分析建立透明3D打印面罩的生物力学模型。
  • 招募10例6个月内面部深度烧伤患者进行临床研究,使用根据生物力学模型设计的3D打印面罩,并测量每例患者的界面压力。
  • 治疗组(n=5)在初始瘢痕评估后立即使用3D打印透明面罩,延迟治疗组(n=5)在初始瘢痕评估后1个月开始治疗,两组均在干预后1个月进行瘢痕评估。

主要发现

  • 生物力学建模显示,若不纳入设计修改以解决相关问题,3D计算机生成的面罩会导致压力不平衡。
  • 通过个体化设计调整和添加硅胶衬里优化了面罩与患者面部的界面压力。
  • 通过额外衬里优化压力后,全部10例患者瘢痕的平均厚度和硬度在干预1个月后显著降低。
  • 在延迟治疗组中,未干预的1个月内瘢痕平均厚度增加,但干预后也降低。

临床怎么用

  • 原文未据此给出推荐。

局限性

  • 原文未报告局限性。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

INTRODUCTION: Deep facial burns leave conspicuous scar to the patients and affect their quality of life. Transparent facemask has been adopted for the prevention and treatment of facial hypertrophic scars for decades. Recently, with the advancement of 3D printing, the transparent facemask could facilitate the fitting of the facial contour. However, the effectiveness of the device and its biomechanical characteristics on pressure management of hypertrophic scar would need more objective evaluation. METHOD: A biomechanical model of the transparent 3D-printed facemask was established through finite element analysis. Ten patients with extensive deep facial burns within 6 months were recruited for clinical study using 3D-printed facemask designed according to biomechanical model, and the interface pressure was measured on each patient. The patients in the treatment group (n=5) was provided with the 3D-printed transparent face mask soon after initial scar assessment, while the delayed treatment group (n=5) began the treatment one month after the initial scar assessment. The scar assessment was performed one month post intervention for both groups. RESULTS: The biomechanical modeling showed that the 3D, computer-generated facemask resulted in unbalanced pressure if design modifications were not incorporated to address these issues. The interface pressure between the facemask and patient's face was optimized through individualized design adjustments and the addition of silicone lining. After optimization of pressure through additional lining, the mean thickness and hardness of the scars of all 10 patients were decreased significantly after 1-month of intervention. In the delayed treatment group, the mean thickness of the scars was increased within the month without intervention, but it was also decreased after intervention. CONCLUSION: Facemask design and the silicone lining are important to ensure adequate compression pressure of 3D-printed transparent facemask. The intervention using the 3D-printed facemask appeared to show its efficacy to control the thickness and hardness of the facial hypertrophic scars.

来源:Burns,查看原文。版权归原作者所有。

引用

  1. Wei Y, Wang Y, Zhang M, et al. The application of 3D-printed transparent facemask for facial scar management and its biomechanical rationale. Burns. 2017. PMID: 29032976. doi:10.1016/j.burns.2017.08.006

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。