文献速递美容整形

三维模拟与三维打印用于患者特异性隆鼻术

Patient-Specific Augmentation Rhinoplasty Using a Three-Dimensional Simulation Program and Three-Dimensional Printing.
PubMed 文献 · Aesthet Surg J · 2017-01-01

本研究在临床试验中通过可重复性测试验证三维雕刻模拟与患者特异性植入物制作系统的可行性;用术前CT设计植入物,经3D打印负模具灌注硅胶制作10个实际植入物,与虚拟设计比较,并观察7例患者术后CT确认位置。

要点

  • 虚拟设计植入物与实际制作植入物差异为0.17%±0.11%,制作精度在0.07 mm内。
  • 植入物间隙百分比在头端最高,由头端向尾端递减。
  • 7例患者术后CT用于确认植入物定位,系统可更直观、快速、准确制作植入物。

核心结论

  • 三维雕刻系统可更直观、快速、准确地制作植入物,且不受术者经验水平影响,从而辅助隆鼻术。

研究设计与样本

  • 临床试验中使用可重复性测试验证三维雕刻模拟与患者特异性植入物制作系统;制作10个实际硅胶植入物与虚拟设计比较,7例患者接受手术及术后CT。

主要发现

  • 虚拟设计植入物被制作成实际植入物,差异在0.07 mm内,为0.17%±0.11%。
  • 间隙百分比在植入物头端最高并向尾端降低:最头端点100%;鼻骨尾端最右和最左点分别为57.1%和71.4%;鼻尖上区折点最右和最左点均为28.6%;最尾端点0%。

临床怎么用

  • 可利用术前CT进行患者特异性植入物设计,经3D打印负模具灌注硅胶制作,并用术后CT确认植入物定位。

局限性

  • 证据等级为4级。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

BACKGROUND: The convergence of three-dimensional (3D) simulation, tissue engineering, and 3D printing technology is creating a paradigm shift in plastic surgery. In augmentation rhinoplasty, determining the ideal material and design method has been a critical issue for many years. Thus, these technologies are expected to make important contributions to augmentation rhinoplasty. OBJECTIVES: We sought to validate the feasibility of the 3D carving simulation and patient-specific implant fabrication system (3D carving system) in a clinical trial using reproducibility tests. METHODS: Patient-specific implants were designed using a program developed in-house with preoperative computed tomography (CT). Negative molds of the implant were fabricated by a 3D printer and silicone was injected into these molds. Ten actual silicone implants were fabricated and compared with virtually designed implants. Seven patients underwent surgery and postoperative CT to confirm implant positioning. RESULTS: Virtually designed implants were produced into actual implants within 0.07 mm with a 0.17% ± 0.11% difference. The percentage within the gap was the highest at the cephalic end of the implant and reduced from the cephalic to caudal end (most cephalic point: 100%; rightmost and leftmost point of the implant at the caudal end of the nasal bone: 57.1% and 71.4%, respectively; rightmost and leftmost point at the supratip break: 28.6% and 28.6%, respectively; and most caudal point: 0%). CONCLUSIONS: The 3D carving system can facilitate rhinoplasty by enabling the more intuitive, rapid, and accurate fabrication of implants irrespective of surgeon experience level. LEVEL OF EVIDENCE: 4.

来源:Aesthet Surg J,查看原文。版权归原作者所有。

引用

  1. Choi YD, Kim Y, Park E, et al. Patient-Specific Augmentation Rhinoplasty Using a Three-Dimensional Simulation Program and Three-Dimensional Printing. Aesthet Surg J. 2017. PMID: 28520846. doi:10.1093/asj/sjx046

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。