文献速递乳房整形与再造显微修复重建

三维打印导板与血管模型在乳房再造中穿支定位的临床价值

Clinical utility of a 3D-printed guide and vascular model for deep and superficial inferior epigastric vessels in breast reconstruction.
PubMed 文献 · J Plast Reconstr Aesthet Surg · 2026-09-10

该回顾性研究纳入130例腹部皮瓣乳房再造患者,比较CTA三维打印个体化导板与单纯CTA规划的效果。三维打印组整体皮瓣获取时间更短(184.0 vs. 158.0分钟,p=0.039),单侧单蒂DIEP皮瓣获取时间亦更短(182.5 vs. 158.0分钟,p=0.025),且筋膜切开长度更短、术后第3-5天VAS疼痛评分更低,阿片类消耗与并发症相当。

要点

  • 三维打印导板可缩短DIEP皮瓣获取时间,尤其单侧单蒂时。
  • 导板辅助可减少筋膜切开长度并降低术后早期疼痛评分。
  • 导板对SIEV术中定位的中位横向偏差为1.00毫米。

核心结论

  • 三维打印工作流程与单蒂DIEP皮瓣获取时间缩短和筋膜切开长度减少相关,可能提高手术效率,但临床意义需进一步研究。

研究设计与样本

  • 回顾性对照研究,纳入2024年6月至2025年9月腹部皮瓣乳房再造患者130例,其中单纯CTA组75例、三维打印组55例。

主要发现

  • 三维打印组整体皮瓣获取时间更短(184.0 vs. 158.0分钟,p=0.039)。
  • 单侧单蒂DIEP皮瓣获取时间更短(182.5 vs. 158.0分钟,p=0.025)。
  • 单蒂DIEP皮瓣筋膜切开长度更短,术后第3-5天VAS疼痛评分更低(均p<0.05)。
  • 阿片类消耗和并发症两组相当。
  • 两种CTA来源DIEP体表标记的中位径向偏差为5.05毫米,导板标记与术中SIEV定位的中位横向偏差为1.00毫米。

临床怎么用

  • 对于单蒂DIEP皮瓣乳房再造,可考虑使用CTA来源的三维打印导板和血管模型辅助术前规划与术中穿支定位。

局限性

  • 回顾性研究设计,样本量有限,临床意义需进一步研究确定。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

BACKGROUND: Although 3D-printing has been applied across multiple surgical fields, comparative evidence for computed tomography angiography (CTA)-derived patient-specific guides in abdominal-based breast reconstruction remains limited. We evaluated a CTA-derived 3D-printed surgical guide and vascular model incorporating both deep and superficial inferior epigastric vessels. METHODS: We retrospectively reviewed abdominal-based breast reconstructions from June 2024 to September 2025 by comparing patient-specific 3D-printed and CTA-only planning data. Outcomes of interest included flap harvest time, postoperative pain, complications, discrepancy between guide-based and manual CTA-derived deep inferior epigastric perforator (DIEP) surface markings, and discrepancy between guide-based superficial inferior epigastric vein (SIEV) markings and intraoperatively identified SIEV locations. RESULTS: Among the 130 patients (CTA-only, n=75; 3D-printed, n=55), the 3D-printed group had shorter overall flap harvest time (184.0 vs. 158.0 min; p=0.039) and shorter harvest time for unilateral, unipedicled DIEP flaps (182.5 vs. 158.0 min; p=0.025). Fasciotomy length in unipedicled DIEP flaps was shorter and visual analog scale pain scores from postoperative days 3-5 were lower in the 3D-printed group (all p<0.05), whereas opioid consumption and complications were comparable between the groups. The median radial discrepancy between the two CTA-derived DIEP surface-marking methods was 5.05 mm and median lateral discrepancy between the guide-based marking and intraoperatively identified SIEV location was 1.00 mm. CONCLUSIONS: The 3D-printed workflow was associated with shorter flap harvest time and shorter fasciotomy length in unipedicled DIEP flaps. These findings indicate a potential improvement in operative efficiency and further studies are needed to determine its clinical significance.

来源:J Plast Reconstr Aesthet Surg,查看原文。版权归原作者所有。

引用

  1. Bae J, Woo KJ, Choi Y, et al. Clinical utility of a 3D-printed guide and vascular model for deep and superficial inferior epigastric vessels in breast reconstruction. J Plast Reconstr Aesthet Surg. 2026. PMID: 42810311. doi:10.1016/j.bjps.2026.09.009

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。