3D打印静态渐进性张口矫治器改善烧伤后张口受限的疗效
本研究开发并评估了一种由临床医生与两名烧伤幸存者共同设计的可定制3D打印静态渐进性张口矫治器,用于治疗六名成年烧伤幸存者。采用口部损伤与残疾评估(MIDA)进行前后对比,结果显示垂直和水平张口度及MIDA评分随治疗和时间显著改善,矫治器材料成本约2-3美元。
要点
- 3D打印静态渐进性张口矫治器可显著改善烧伤后小口畸形患者的垂直和水平张口度及MIDA评分。
- 推荐佩戴方案为每日2-3次、每次10-15分钟,佩戴后完成治疗活动和口部练习。
- 该矫治器材料成本约2-3美元,所有3D打印文件公开可用,适合资源匮乏地区。
核心结论
- 3D打印静态渐进性张口矫治器能显著改善烧伤后小口畸形患者的张口度和口部功能,且成本低廉、可定制。
研究设计与样本
- 前瞻性前后对比研究,纳入六名成年烧伤幸存者,使用MIDA进行评估,并分析成本效益。
主要发现
- 垂直和水平张口度及MIDA评分随治疗和时间显著改善。
- 矫治器材料成本约2-3美元。
- 患者佩戴方案为每日2-3次、每次10-15分钟,随后完成治疗活动和口部练习。
关键数值与推荐
- 张口矫治器由临床医生与两名烧伤幸存者共同设计,可定制。
- 推荐佩戴方案:每日2-3次,每次10-15分钟。
- 疗效评估采用口部损伤与残疾评估(MIDA)。
临床怎么用
- 对于烧伤后小口畸形患者,可考虑使用3D打印静态渐进性张口矫治器以改善张口度和功能。
- 佩戴矫治器后应配合治疗活动和口部练习。
- 在资源匮乏地区,该低成本、可及性高的矫治器具有应用价值。
局限性
- 样本量小(六名患者),未设对照组,结果需更大样本验证。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
Microstomia, often observed following facial burn injuries, can hinder functional activities such as eating, speaking, dental care, and medical procedures such as intubation. To address these challenges, microstomia orthoses (MO) are used to increase mouth opening and function. Many versions of MOs have been described from hand-crafted to commercially available models. However, proposed options can be quite expensive based on fabrication time or materials, and not all models can be customized for patient's needs. 3D printing presents a promising alternative for fabricating MOs, addressing many of the limitations of currently used methods. The purpose of this study was to develop and evaluate the efficacy of a 3D-printed static-progressive MO in increasing mouth opening and improving functional outcomes. The orthosis was used to treat six adult burn survivors with pre-post evaluation using the Mouth Impairment and Disability Assessment (MIDA). The cost-effectiveness of this 3D MO was also investigated. A customizable 3D-printed static-progressive MO was co-designed by clinicians and two burn survivors, which cost approximately $2-3 USD of materials to produce. The prescribed wearing regime of this 3D-printed static-progressive MO resulted in significant improvement of vertical and horizontal mouth opening and MIDA scores with treatment and time. These results were achieved with patients wearing the MO 2-3x/day for 10-15 min, followed by completing their therapeutic activities and mouth exercises after wearing the MO. The global accessibility, low cost, and relative efficiency of this orthosis will be invaluable, particularly in resource poor regions. All 3D-printable files for this 3D-printed MO are publicly available (Appendix 1).
引用
- Edger-Lacoursière Z, Phung M, Calva V, et al. Efficacy of a 3D-printed static progressive microstomia orthosis in increasing mouth opening and function following burn injury. Burns. 2025. PMID: 41109163. doi:10.1016/j.burns.2025.107707
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。