通过有限元分析评估3D打印植入物在鼻中隔鼻整形术中的机械强度
本研究通过有限元分析比较3D打印丝素蛋白-明胶(SFG)、聚己内酯(PCL)和聚乳酸(PLA)植入物与鼻中隔软骨的机械强度。结果显示3D打印实性SFG、PCL、PLA及支架PCL、PLA模型的形变低于软骨,实性SFG兼顾强度与柔韧性,最大应力低于所有材料的屈服应力,作者认为支架SFG需进一步几何优化以用于软骨替代。
要点
- 3D打印实性SFG、PCL、PLA及支架PCL、PLA的形变均低于软骨。
- 实性SFG兼顾强度与柔韧性,其力学行为与软骨相似。
- 所有材料最大应力均低于屈服应力,日常载荷下形变不太可能为永久性。
核心结论
- 作者有限元模型提示3D打印L形支撑植入物具有值得期待的机械强度。
- 实性SFG结果模拟了软骨的力学行为,支架SFG需进一步几何优化以潜在用于软骨替代。
- 3D打印鼻中隔软骨替代植入物在特定情形下可能改善缺乏供区软骨患者的手术处理。
研究设计与样本
- 有限元分析模型比较3D打印实性与支架植入物替代软骨的应力和形变响应。
- 在keystone区域施加单向载荷以模拟每日来自覆盖软组织的力,并与原生软骨特性比较。
主要发现
- 3D打印实性SFG、PCL、PLA及支架PCL、PLA模型较软骨表现出更低的形变。
- 实性SFG平衡了强度与柔韧性。
- 最大应力低于所有材料的屈服应力,提示日常载荷下其形变不太可能为永久性。
关键数值与推荐
- 临床问题/证据等级:治疗性,V级。
临床怎么用
- 计算模拟可评估3D打印植入物的强度及其在鼻中隔鼻整形术中替代鼻中隔软骨的潜力。
局限性
- 原文未报告局限性
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
BACKGROUND: Autologous nasoseptal cartilage grafts are used to correct nasal asymmetry and deviation in rhinoplasty, but patients who have undergone multiple operations may have limited autologous cartilage tissue available. L-strut implants created on a 3-dimensional (3D) printer may address these challenges in the future, but their mechanical strength is understudied. Silk fibroin-gelatin (SFG), polycaprolactone (PCL), and polylactide (PLA) are bioinks known for their strength. The authors present finite element analysis (FEA) models comparing the mechanical strength of 3D-printed SFG, PCL, and PLA implants with nasoseptal cartilage grafts when autologous or allografts are not available. METHODS: FEA models compared the stress and deformation responses of 3D-printed solid and scaffold implant replacements to cartilage. To simulate a daily force from overlying soft tissue, a unidirectional load was applied at the "keystone" region given its structural role and compared with native cartilaginous properties. RESULTS: The 3D-printed solid SFG, PCL, and PLA and scaffold PCL and PLA models demonstrated lower deformations compared with cartilage. Solid SFG balanced strength and flexibility. The maximum stress was below all materials' yield stresses, suggesting that their deformations are unlikely permanent under a daily load. CONCLUSIONS: The authors' FEA models suggest that 3D-printed L-strut implants carry promising mechanical strength. Solid SFG results mimicked cartilage's mechanical behavior. Thus, scaffold SFG merits further geometric optimization for potential use for cartilage substitution. The 3D-printed septal cartilage replacement implants can potentially enhance surgical management of patients who lack available donor cartilage in select settings. CLINICAL RELEVANCE STATEMENT: Computational simulations can evaluate the strength of 3D-printed implants and their potential to replace septal cartilage in septorhinoplasty. CLINICAL QUESTION/LEVEL OF EVIDENCE: Therapeutic, V.
引用
- Syamal S, Taritsa IC, Alvarez AH, et al. Evaluating the Mechanical Strength of 3-Dimensionally Printed Implants in Septorhinoplasty through Finite Element Analysis. Plast Reconstr Surg. 2024. PMID: 38923894. doi:10.1097/PRS.0000000000011600
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。