定制3D压力传感器面罩在面部烧伤瘢痕中的应用:一项单盲随机对照试验
该单盲前瞻性随机对照试验于2023年5月至10月纳入12例面部烧伤住院患者的48处瘢痕,评估内衬生物相容性硅胶、可连续监测15-25 mmHg压力的定制3D打印面罩。应用12周后,3D面罩组较对照组皮肤水合显著增加、瘢痕厚度显著降低,VSS和POSAS多项参数显著改善。
要点
- 定制3D面罩内置压力传感器,可连续监测15-25 mmHg有效压力。
- 应用12周后3D面罩组皮肤水合显著增加、瘢痕厚度显著降低。
- VSS的柔软度和高度、POSAS患者与观察者分量表多项参数显著改善。
核心结论
- 定制3D压力传感器面罩在12周应用期间显著改善瘢痕厚度、皮肤水合及多项评估量表参数。
研究设计与样本
- 单盲前瞻性随机对照试验,于2023年5月至10月纳入12例面部烧伤住院患者的48处烧伤瘢痕。
- 采用3D打印技术制作内衬生物相容性硅胶、配备压力传感器和束带系统的定制3D压迫面罩,可连续监测是否维持15-25 mmHg适当压力。
主要发现
- 应用前3D面罩组与对照组在生物学瘢痕特性、VSS和POSAS评分上差异均无统计学意义(p均>0.05)。
- 12周应用期间,3D面罩组较对照组皮肤水合显著增加(p<0.001)、瘢痕厚度显著降低(p=0.010)。
- 12周应用期间,3D面罩组VSS的柔软度(p=0.004)和高度(p=0.009)较对照组显著改善。
- 12周应用期间,3D面罩组POSAS患者分量表瘙痒(p=0.047)、瘢痕僵硬(p=0.001)、厚度(p=0.011)和不规则度(p<0.001)较对照组显著改善。
- 12周应用期间,3D面罩组POSAS观察者分量表瘢痕厚度(p=0.001)、柔软度(p=0.012)和表面积(p=0.027)较对照组显著改善。
关键数值与推荐
- 有效压迫治疗采用约15-25 mmHg的压力,以预防和治疗烧伤患者的增生性瘢痕。
临床怎么用
- 原文未据此给出推荐。
局限性
- 原文未报告局限性。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
PURPOSE: A pressure of approximately 15-25 mmHg is used for effective compression therapy to prevent and treat hypertrophic scar formation in patients with burns. However, conventional facial compression garments present challenges owing to inadequate pressure distribution in curved areas such as the cheeks, around the mouth, and the slope of the nose. This study aimed to evaluate the utility of a custom-made 3D compression mask equipped with pressure sensors to treat facial burn scars. METHODS: This single-blinded, prospective randomized controlled trial was conducted between May and October 2023, involving 48 burn scars in 12 inpatients with facial burns. We created the custom-made 3D compression mask equipped with pressure sensors, inner lined with biocompatible silicon, and a harness system using 3D printing technology, which can continuously monitor whether an appropriate pressure of 15-25 mmHg maintains. The biological scar properties, Vancouver Scar Scale (VSS), and Patient and Observer Scar Assessment Scale (POSAS) scores in patients with facial burns were assessed before applying the compression mask and garment and at 4 and 12 weeks after application. RESULTS: Pre-application assessment of biological scar properties, VSS, and POSAS revealed no statistically significant differences between the 3D mask and control groups (p > 0.05 for all). Throughout the 12-week application, skin hydration and scar thickness significantly increased (p < 0.001) and reduced (p = 0.010), respectively, in the 3D mask group compared to the control group. Additionally, significant improvements in scar pliability (p = 0.004) and height (p = 0.009) of VSS, itching (p = 0.047), scar stiffness (p = 0.001), thickness (p = 0.011), and irregularity (p < 0.001) of POSAS-patient component, and scar thickness (p = 0.001), pliability (p = 0.012), and surface area (p = 0.027) of the POSAS-observer component were observed in 3D mask group throughout the 12-week application compared to the control group. CONCLUSION: The customized 3D compression mask equipped with pressure sensors significantly improved scar thickness, skin hydration, and various assessment scale parameters throughout the 12-week application.
引用
- Hwang SJ, Seo J, Cha JY, et al. Utility of customized 3D compression mask with pressure sensors on facial burn scars: A single-blinded, randomized controlled trial. Burns. 2024. PMID: 38937166. doi:10.1016/j.burns.2024.05.021
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。