切割平面对肋软骨翘曲的影响
研究从10具新鲜尸体取207块肋软骨移植物,沿头尾、前后及平行于软骨结合面三个主要平面切割,每平面再分中央与周边、厚度1、2、3 mm亚组,比较切割后不同时间点的翘曲角度。结果头尾切割翘曲显著大于其他平面,前后切割翘曲最小但差异无统计学意义,翘曲峰值在30分钟,部分移植物至1个月仍继续翘曲。
要点
- 头尾切割翘曲角度最大,前后切割翘曲最小但差异无统计学意义。
- 翘曲峰值出现在切割后30分钟,部分移植物至1个月仍继续翘曲。
- 中央移植物翘曲小于周边移植物,但差异无统计学意义。
核心结论
- 头尾切割产生最大翘曲角度。
- 寻求薄(<3 mm)直移植物者应选择前后或平行于软骨结合面切割。
- 厚移植物(>3 mm)可行头尾切割,翘曲角度可接受,接近平行于软骨结合面切割。
- 对于弯曲软骨,推荐薄层头尾切割。
- 作者建议将软骨置于生理盐水中至少30分钟,使最大翘曲发生。
研究设计与样本
- 从10具新鲜尸体取207块肋软骨移植物,沿头尾、前后及平行于软骨结合面三个主要平面切割,每平面再分中央与周边,各亚组再分1、2、3 mm三种厚度,比较切割后不同时间点的翘曲角度。
主要发现
- 头尾切割翘曲显著大于其他平面。
- 前后切割翘曲最小,但差异无统计学意义。
- 翘曲峰值出现在30分钟。
- 部分移植物至1个月仍继续翘曲。
- 中央移植物翘曲小于周边移植物,但差异无统计学意义。
临床怎么用
- 作者建议寻求薄(<3 mm)直移植物者选择前后或平行于软骨结合面切割。
- 作者建议厚移植物(>3 mm)可行头尾切割,翘曲角度可接受,接近平行于软骨结合面切割。
- 作者建议弯曲软骨行薄层头尾切割。
- 作者建议将软骨置于生理盐水中至少30分钟,使最大翘曲发生。
局限性
- 原文未报告局限性
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
BACKGROUND: Autogenous costal cartilage becomes a favorable choice for nasal reconstruction and complicated aesthetic rhinoplasty, because of its ample supply, sufficient for most patients. However, a notable drawback is the potential for warping. The authors' study aims to identify cutting planes that minimize warping. METHODS: Two hundred seven costal cartilage grafts were obtained by slicing the extracted costal cartilages from 10 fresh cadavers along 3 main planes: cephalocaudal, anteroposterior, and parallel to the synchondrosis plane. Each of these major planes was further divided into grafts taken from both the central and peripheral portions. Furthermore, both subgroups were categorized into three thicknesses: 1, 2, and 3 mm. The warping angles of all grafts were then compared at various time intervals after the initial cutting. RESULTS: Cephalocaudal cuts exhibited significantly greater warping than other planes. Anteroposterior cuts displayed the least warping, although this difference lacked statistical significance. Peak warping occurred at 30 minutes. Certain grafts continued to warp even at 1 month. Central grafts had less warping than peripheral ones, although the difference was not statistically significant. CONCLUSIONS: Cephalocaudal cuts yielded the highest warping angle. Surgeons seeking thin (<3 mm) straight grafts should opt for anteroposterior or parallel to synchondrosis planes. Thicker grafts (>3 mm) can be cut in the cephalocaudal plane with an acceptable warping angle, close to parallel with the synchondrosis plane. For curved cartilage, thin cephalocaudal cutting is recommended. In addition, the authors suggest placing the cartilage in normal saline for at least 30 minutes, allowing for maximum warping to occur.
引用
- Ratanapoompinyo S, Kiranantawat K. Effects of Cutting Planes on Costal Cartilage Warping. Plast Reconstr Surg. 2024. PMID: 38616315. doi:10.1097/PRS.0000000000011470
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。