翻修全髋关节置换中大头径股骨头与双动轴承脱位率无差异
该回顾性研究比较了301例翻修全髋关节置换中标准轴承与双动轴承(股骨头≥40-mm)的术后脱位率,平均随访37.1个月。结果显示标准轴承脱位率5.7%,双动轴承6.9%,差异无统计学意义(P=1.000)。多因素分析中低体重指数、女性和股骨头外径与髋臼杯尺寸比值降低是脱位的预测因素。
要点
- 翻修全髋中股骨头≥40-mm时,标准轴承与双动轴承脱位率无显著差异。
- 总体脱位率为8.6%(22/257)。
- 低BMI、女性、股骨头外径/杯尺寸比值降低是脱位预测因素。
核心结论
- 在翻修全髋关节置换中,使用股骨头≥40-mm时,标准轴承与双动轴承的术后脱位率无差异。
- 考虑到双动轴承的成本和额外界面潜在问题,应审慎使用,因为单关节大直径股骨头轴承可能达到相似结果。
研究设计与样本
- 回顾性综述301例连续翻修全髋关节置换,平均随访37.1个月。
- 比较股骨头≥40-mm的标准轴承(182例)与双动轴承(75例),以隔离双关节活动的影响。
- 结局为术后脱位和90天内再手术。
主要发现
- 总体脱位率为8.6%(22/257)。
- 标准轴承(股骨头≥40-mm)脱位率为5.7%,双动轴承(股骨头≥40-mm)为6.9%(P=1.000)。
- 多因素分析中,低体重指数(比值比1.72)、女性(比值比2.01)和股骨头外径与髋臼杯尺寸比值降低(比值比1.64)是术后脱位的预测因素,与轴承类型无关。
临床怎么用
- 在翻修全髋关节置换中,对于股骨头≥40-mm的病例,可考虑使用标准轴承以降低成本,同时预期脱位率与双动轴承相似。
- 对于低体重指数、女性或股骨头外径与髋臼杯尺寸比值降低的患者,应警惕术后脱位风险。
局限性
- 本研究为回顾性设计,证据等级为III级。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
BACKGROUND: Dual-mobility (DM) bearings reduce instability in revision total hip arthroplasty (THA); however, DM bearings are costly and reports of corrosion have recently emerged. Furthermore, no study has compared DM to standard bearings with large diameter femoral heads ≥40-mm. This study's purpose was to compare postoperative dislocation rates of standard and DM bearings with large femoral heads after revision THA. METHODS: A retrospective review of 301 consecutive revision THAs was performed. The mean follow-up was 37.1 months. To isolate the effect of the double articulation, standard and DM bearings with femoral heads ≥40-mm were compared. Outcomes were postoperative dislocation and reoperation within 90 days. RESULTS: The cohort consisted of 182 standard bearings and 75 DM bearings. There were no differences in revision indication comparing standard and DM bearings (P = .258). Overall dislocation rate was 8.6% (22 of 257). The dislocation rate was 5.7% for standard bearings with ≥40-mm femoral heads compared with 6.9% in DM bearings with ≥40-mm femoral heads (P = 1.000). In multivariate analysis, lower body mass index (odds ratio 1.72), female sex (odds ratio 2.01), and decreased outer femoral head diameter-to-cup component size ratio (odds ratio 1.64) were predictors of postoperative dislocation regardless of bearing type. CONCLUSION: This study showed no difference in dislocation rates between standard and DM bearings when comparing similar femoral head diameters of ≥40-mm used in revision THAs. Considering the cost and potential deleterious issues associated with additional interfaces, DM bearings should be used judiciously considering similar results may be achieved with single-articulation bearings using large femoral heads. LEVEL OF EVIDENCE: Level III.
引用
- Sonn KA, Deckard ER, Meneghini RM, et al. No Difference in Dislocation Rates Comparing Large Diameter Jumbo Femoral Heads and Dual-Mobility Bearings in Revision Total Hip Arthroplasty. J Arthroplasty. 2021. PMID: 34391597. doi:10.1016/j.arth.2021.07.008
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。