文献速递关节外科

3D打印钛金属干骺端锥形套筒在翻修全膝关节置换术中的应用:骨水泥柄与无骨水泥柄的比较

3D-printed titanium metaphyseal cones in revision total knee arthroplasty with cemented and cementless stems.
PubMed 文献 · Bone Joint J · 2021-01-01

本研究回顾性分析了86例翻修全膝关节置换术和9例复杂初次全膝关节置换术,评估使用3D打印干骺端锥形套筒固定时,骨水泥柄与无骨水泥柄对膝关节对线的影响。结果显示锥形套筒无因无菌性松动翻修,但双侧无骨水泥柄组对线不良风险显著增加(OR 3.19,95%CI 1.01-10.05)。

要点

  • 3D打印多孔锥形套筒提供良好的干骺端固定,无因无菌性松动翻修。
  • 双侧无骨水泥柄较双侧骨水泥柄的对线不良风险显著增高(OR 3.19)。
  • 中央锥形套筒使偏移耦合器使用困难,可能增加无骨水泥柄的对线不良。

核心结论

  • 多孔3D打印锥形套筒提供优异的干骺端固定,但中央锥形套筒使偏移耦合器使用困难,无骨水泥柄可能产生对线不良。
  • 使用干骺端锥形套筒且股骨和胫骨均为无骨水泥柄时,对线不良的比值比为3.19(95%CI 1.01-10.05)。

研究设计与样本

  • 回顾性研究,纳入86例翻修全膝关节置换术和9例复杂初次全膝关节置换术,平均年龄63.2岁(SD 8.2),BMI 34.0 kg/m2(SD 8.7)。
  • 根据所用柄的类型比较膝关节对线:22膝双侧无骨水泥柄,52膝双侧骨水泥柄,15膝混合柄。
  • 术后站立位长片X线评估冠状面和矢状面对线,采用调整logistic回归模型分析对线不良(HKA超出±3°及胫骨/股骨组件矢状面对线±3°)与柄类型的关系。

主要发现

  • 无患者因无菌性松动翻修锥形套筒,但2例因感染翻修。
  • 26例(27%)患者存在HKA对线不良;9例(9.5%)存在矢状面对线不良,其中胫骨5例(5.6%),股骨4例(10.8%)。
  • 调整年龄、性别和BMI后,与双侧骨水泥柄相比,双侧无骨水泥柄的对线不良风险显著增加(OR 3.19,95%CI 1.01-10.05)。

关键数值与推荐

  • 对线不良定义为HKA超出±3°及胫骨/股骨组件矢状面对线超出±3°。
  • 双侧无骨水泥柄组对线不良风险显著高于双侧骨水泥柄组(OR 3.19,95%CI 1.01-10.05)。

临床怎么用

  • 3D打印多孔锥形套筒可用于翻修全膝关节置换术的干骺端固定,但选择无骨水泥柄时需警惕对线不良风险。
  • 中央锥形套筒可能限制偏移耦合器的使用,术前应评估是否需要偏移耦合器以辅助对线。

局限性

  • 回顾性研究设计,样本量有限(共95膝),可能存在选择偏倚。
  • 短期随访,未报告长期临床功能结果和锥形套筒的长期存活率。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

AIMS: Porous metaphyseal cones can be used for fixation in revision total knee arthroplasty (rTKA) and complex TKAs. This metaphyseal fixation has led to some surgeons using shorter cemented stems instead of diaphyseal engaging cementless stems with a potential benefit of ease of obtaining proper alignment without being beholden to the diaphysis. The purpose of this study was to evaluate short term clinical and radiographic outcomes of a series of TKA cases performed using 3D-printed metaphyseal cones. METHODS: A retrospective review of 86 rTKAs and nine complex primary TKAs, with an average age of 63.2 years (SD 8.2) and BMI of 34.0 kg/m2 (SD 8.7), in which metaphyseal cones were used for both femoral and tibial fixation were compared for their knee alignment based on the type of stem used. Overall, 22 knees had cementless stems on both sides, 52 had cemented stems on both sides, and 15 had mixed stems. Postoperative long-standing radiographs were evaluated for coronal and sagittal plane alignment. Adjusted logistic regression models were run to assess malalignment hip-knee-ankle (HKA) alignment beyond ± 3° and sagittal alignment of the tibial and femoral components ± 3° by stem type. RESULTS: No patients had a revision of a cone due to aseptic loosening; however, two had revision surgery due to infection. In all, 26 (27%) patients had HKA malalignment; nine (9.5%) patients had sagittal plane malalignment, five (5.6%) of the tibia, and four (10.8%) of the femur. After adjusting for age, sex, and BMI, there was a significantly increased risk for malalignment when a cone was used and both the femur and tibia had cementless compared to cemented stems (odds ratio 3.19, 95% confidence interval 1.01 to 10.05). CONCLUSION: Porous 3D-printed cones provide excellent metaphyseal fixation. However, these central cones make the use of offset couplers difficult and may generate malalignment with cementless stems. We found 3.19-times higher odds of malalignment in our TKAs performed with metaphyseal cones and both femoral and tibial cementless stems. Cite this article: Bone Joint J 2021;103-B(6 Supple A):150-157.

来源:Bone Joint J,查看原文。版权归原作者所有。

引用

  1. Anderson LA, Christie M, Blackburn BE, et al. 3D-printed titanium metaphyseal cones in revision total knee arthroplasty with cemented and cementless stems. Bone Joint J. 2021. PMID: 34053297. doi:10.1302/0301-620X.103B6.BJJ-2020-2504.R1

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。