文献速递关节外科

非骨水泥整体聚乙烯髋臼假体的解剖性骨盆负载

Anatomical pelvic loading of a monoblock polyethylene acetabular component.
PubMed 文献 · Bone Joint J · 2021-01-01

前瞻性纳入38例患者接受非骨水泥钛烧结整体聚乙烯髋臼假体,并与既往 cemented 和 trabecular 金属假体随机队列回顾性比较。主要终点为双能X线吸收法测定的假体周围骨密度,随访两年。结果显示该假体初期类似 trabecular 金属假体(外侧缘负载),随后内侧骨密度回升,更接近骨水泥聚乙烯假体的负载模式。

要点

  • 非骨水泥整体聚乙烯髋臼假体初期呈外侧缘负载,类似trabecular金属假体。
  • 两年内内侧骨密度回升至基线,负载模式转向类似骨水泥聚乙烯假体。
  • 影像学未见假体下沉或移位,术后内侧骨缺损多数完全愈合。

核心结论

  • 非骨水泥整体聚乙烯髋臼假体初期类似刚性trabecular金属假体的外侧缘负载,两年内逐渐转为更接近骨水泥聚乙烯假体的内侧骨盆负载增加模式。
  • 该假体可能实现优化的固定并保留髋臼后部骨量。

研究设计与样本

  • 前瞻性单队列纳入38例患者接受非骨水泥整体聚乙烯髋臼假体(pressfit),并回顾性比较既往报道的骨水泥整体假体和trabecular金属假体随机队列。
  • 主要终点为双能X线吸收法测定的假体周围骨密度,随访两年;次要终点包括影像学和临床分析。

主要发现

  • 三组间性别分布差异无统计学意义(p=0.080),年龄(p=0.910)和基线腰椎骨密度(p=0.998)均无显著差异。
  • pressfit假体初期下部和内侧区域骨密度立即下降,外侧骨密度保留,提示外侧缘负载。
  • pressfit假体随后内侧骨密度回升至基线,外侧骨密度持续上升。
  • 术后X线片显示两年内无pressfit假体下沉或移位(观察者间信度100%)。
  • 术后即刻发现的5例内侧骨缺损中,4例在两年时完全愈合。

临床怎么用

  • 该非骨水泥整体聚乙烯髋臼假体可能提供骨整合与解剖性负载的优化组合,有助于保留髋臼后部骨量。

局限性

  • pressfit组为前瞻性单队列,与既往随机队列进行回顾性比较,非同期随机对照。
  • 各组男女数量存在差异,虽无显著性别偏倚(p=0.080),仍可能影响比较。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

AIMS: Uncemented metal acetabular components show good osseointegration, but material stiffness causes stress shielding and retroacetabular bone loss. Cemented monoblock polyethylene components load more physiologically; however, the cement bone interface can suffer fibrous encapsulation and loosening. It was hypothesized that an uncemented titanium-sintered monoblock polyethylene component may offer the optimum combination of osseointegration and anatomical loading. METHODS: A total of 38 patients were prospectively enrolled and received an uncemented monoblock polyethylene acetabular (pressfit) component. This single cohort was then retrospectively compared with previously reported randomized cohorts of cemented monoblock (cemented) and trabecular metal (trabecular) acetabular implants. The primary outcome measure was periprosthetic bone density using dual-energy x-ray absorptiometry over two years. Secondary outcomes included radiological and clinical analysis. RESULTS: Although there were differences in the number of males and females in each group, no significant sex bias was noted (p = 0.080). Furthermore, there was no significant difference in age (p = 0.910) or baseline lumbar bone mineral density (BMD) (p = 0.998) found between any of the groups (pressfit, cemented, or trabecular). The pressfit implant initially behaved like the trabecular component with an immediate fall in BMD in the inferior and medial regions, with preserved BMD laterally, suggesting lateral rim loading. However, the pressfit component subsequently showed a reversal in BMD medially with recovery back towards baseline, and a continued rise in lateral BMD. This would suggest that the pressfit component begins to reload the medial bone over time, more akin to the cemented component. Analysis of postoperative radiographs revealed no pressfit component subsidence or movement up to two years postoperatively (100% interobserver reliability). Medial defects seen immediately postoperatively in five cases had completely resolved by two years in four patients. CONCLUSION: Initially, the uncemented monoblock component behaved similarly to the rigid trabecular metal component with lateral rim loading; however, over two years this changed to more closely resemble the loading pattern of a cemented polyethylene component with increasing medial pelvic loading. This indicates that the uncemented monoblock acetabular component may result in optimized fixation and preservation of retroacetabular bone stock. Cite this article: Bone Joint J 2021;103-B(5):872-880.

来源:Bone Joint J,查看原文。版权归原作者所有。

引用

  1. Young PS, Macarico DT, Silverwood RK, et al. Anatomical pelvic loading of a monoblock polyethylene acetabular component. Bone Joint J. 2021. PMID: 33934654. doi:10.1302/0301-620X.103B5.BJJ-2020-1321.R2

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。