全髋关节置换陶瓷对陶瓷轴承破裂:发生率、危险因素与结局
氧化铝破裂率高于混合陶瓷(HR 2.50),36-38mm头尺寸使用氧化铝时破裂风险更高(HR 2.84)。第二次翻修风险高且发生早,最佳翻修方案尚不明确。
要点
- 氧化铝轴承破裂率显著高于混合陶瓷(HR 2.50,95%CI 1.75-3.59,P<.001)。
- 36-38mm头尺寸使用氧化铝时破裂风险更高(HR 2.84,95%CI 1.52-5.31,P=.001)。
- 混合陶瓷15年随访破裂发生率为0.79/1000,第二次翻修风险高且发生早。
核心结论
- 混合陶瓷降低了陶瓷破裂发生率,但15年随访仍有0.79/1000的发生率。
- 现代陶瓷的危险因素尚不明确,头尺寸增大仅为氧化铝的危险因素。
- 第二次翻修风险高且发生早,最佳翻修方案未知。
研究设计与样本
- 共纳入23,534例氧化铝和71,144例混合陶瓷(氧化铝/氧化锆)手术。
主要发现
- 氧化铝组84例(占所有翻修的5.27%,占手术的0.36%)因破裂行第一次翻修;混合陶瓷组56例(占所有翻修的2.46%,占手术的0.08%)。
- 氧化铝破裂率高于混合陶瓷(HR 2.50,95%CI 1.75-3.59,P<.001)。
- 36-38mm头尺寸使用氧化铝时破裂风险更高(HR 2.84,95%CI 1.52-5.31,P=.001)。
- 17.8%的第二次翻修发生在3年内,原因为脱位、感染、金属相关病变和松动。
- 颈部适配器套筒未减少第二次翻修。
关键数值与推荐
- 氧化铝因破裂行第一次翻修占所有翻修的5.27%、占手术的0.36%。
- 混合陶瓷因破裂行第一次翻修占所有翻修的2.46%、占手术的0.08%。
- 混合陶瓷15年随访破裂发生率为0.79/1000。
临床怎么用
- 选择陶瓷对陶瓷轴承时需考虑陶瓷类型,氧化铝破裂风险高于混合陶瓷。
- 使用氧化铝轴承时应避免36-38mm头尺寸以降低破裂风险。
- 翻修术后需警惕早期第二次翻修,常见原因为脱位、感染、金属相关病变和松动。
- 颈部适配器套筒未显示减少第二次翻修的作用。
局限性
- 翻修轴承表面选项比较的样本量过少,无法得出可靠结论。
- 现代陶瓷的危险因素尚不明确。
- 最佳翻修方案未知。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
BACKGROUND: Ceramic-on-ceramic bearing breakage is a rare but significant complication of total hip arthroplasty. This study aimed to identify risk factors for breakage and to determine the outcome of different revision options. METHODS: All ceramic-on-ceramic primary total hip arthroplasty procedures reported to the Australian Joint Replacement Registry from September 1999 to December 2019 were included. Procedures were subdivided into alumina or mixed ceramic (alumina/zirconia). All breakages were identified. The association between ceramic type and head size was assessed. Subsequent revision rates were compared and cause of revision assessed. RESULTS: There were 23,534 alumina and 71,144 mixed ceramic procedures. Breakage was the reason for 1st revision in 84 alumina (5.27% of all revisions and 0.36% of procedures) and 56 mixed ceramic procedures (2.46% of all revisions; 0.08% of procedures). Alumina had a higher breakage rate than mixed ceramic (HR 2.50 (95% CI 1.75, 3.59), P < .001), and breakage was higher for 36-38mm head sizes using alumina (HR 2.84 (1.52, 5.31), P = .001). 17.8% of 2nd revisions occur by 3 years, due to dislocation, infection, metal-related pathology, and loosening. A neck adapter sleeve did not reduce 2nd revisions. Numbers were too low to compare revision bearing surface options. CONCLUSION: Ceramic breakage has reduced with mixed ceramics but has a 0.79/1000 incidence at 15-year follow-up. It is unclear what the risk factors are for modern ceramics with increasing head size a risk for alumina only. Risk of 2nd revision is high and occurs early. The optimal revision option is unknown.
引用
- Hoskins W, Rainbird S, Peng Y, et al. Incidence, Risk Factors, and Outcome of Ceramic-On-Ceramic Bearing Breakage in Total Hip Arthroplasty. J Arthroplasty. 2021. PMID: 33812710. doi:10.1016/j.arth.2021.03.021
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。