全髋翻修治疗脱位:标准头、大头、双动或限制性衬垫的比较
基于澳大利亚骨科协会国家关节置换登记系统1999年9月至2018年12月的数据,纳入因骨关节炎行初次全髋置换后因脱位行首次翻修的1275髋,比较标准头(≤32 mm)、大头(≥36 mm)、双动和限制性髋臼衬垫翻修后的二次翻修率。标准头组全因二次翻修率显著高于限制性衬垫组(HR 1.53,95%CI 1.01-2.30,p=0.044),因脱位行二次翻修率也显著高于限制性衬垫、双动和大头组。
要点
- 标准头全因二次翻修率高于限制性衬垫(HR 1.53,p=0.044)。
- 标准头因脱位二次翻修率高于限制性衬垫(HR 2.44)、双动(HR 2.04)和大头(HR 1.80)。
- 二次翻修最常见原因为脱位,共91例因脱位行二次翻修。
核心结论
- 初次全髋置换后因脱位行首次翻修时,限制性髋臼衬垫、双动衬垫和大头(≥36 mm)是减少后续脱位的选择,标准头尺寸因再脱位行二次翻修率更高。
研究设计与样本
- 回顾性登记系统分析,数据来自澳大利亚骨科协会国家关节置换登记系统1999年9月至2018年12月,纳入因骨关节炎行初次全髋置换后因脱位行首次翻修的1275髋。
主要发现
- 1275髋因假体脱位行首次翻修,其中203髋行二次翻修,全因二次翻修最常见原因为脱位。
- 标准头组全因二次翻修率显著高于限制性髋臼衬垫组(HR 1.53,95%CI 1.01-2.30,p=0.044),其他关节界面间无差异。
- 因脱位行二次翻修共91例,标准头组因脱位二次翻修率高于限制性衬垫(HR 2.44,95%CI 1.30-4.60,p=0.005)、双动(HR 2.04,95%CI 1.03-4.01,p=0.039)和大头(HR 1.80,95%CI 1.09-2.99,p=0.022),其他关节界面间无差异。
关键数值与推荐
- 标准头定义为≤32 mm,大头定义为≥36 mm。
- 证据等级为治疗性III级。
临床怎么用
- 初次全髋置换后因脱位行首次翻修时,可考虑使用限制性髋臼衬垫、双动衬垫或大头(≥36 mm)以降低再脱位风险。
- 标准头尺寸因再脱位行二次翻修率更高,应谨慎用于脱位翻修。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
BACKGROUND: Dislocation remains a leading cause of revision following primary and revision total hip arthroplasty (THA). The aim of the present study was to compare the rate of second revision THA following a major first revision for the treatment of dislocation using an implant with a standard, large head, dual-mobility, or constrained acetabular liner. METHODS: Data were obtained from the Australian Orthopaedic Association National Joint Replacement Registry from September 1999 through December 2018. All primary THAs that had been performed for the treatment of osteoarthritis and subsequently revised for dislocation were included. All revision THA prostheses with a standard head (≤32 mm), large head (≥36 mm), dual-mobility, or constrained acetabular liner that were used for the first revision procedure were identified. The primary outcome measures were the cumulative rates of second revisions for all causes and for a subsequent diagnosis of dislocation for the 4 different constructs used in the first revision. RESULTS: A total of 1,275 hips underwent a major first revision because of prosthesis dislocation, with 203 of these hips going on to have a second revision. The rate of all-cause second revision was significantly higher in the standard-head group compared with the constrained-acetabular-liner group (hazard ratio [HR], 1.53 [95% confidence interval (CI), 1.01 to 2.30]; p = 0.044). There was no difference in the rates of revision between other articulations. The most common cause of second revision for all implants was dislocation. There were a total of 91 second revisions for a diagnosis of dislocation. Standard heads had a higher rate of second revision compared with constrained acetabular liners (HR, 2.44 [95% CI, 1.30 to 4.60]; p = 0.005), dual-mobility implants (HR, 2.04 [95% CI, 1.03 to 4.01]; p = 0.039), and large heads (HR, 1.80 [95% CI, 1.09, 2.99]; p = 0.022). There was no difference in the rates of second revision between other articulations. CONCLUSIONS: Surgeons have a number of options for prostheses when performing a first revision for the treatment of dislocation following a primary THA. The most common cause of a second revision is recurrent dislocation. The use of constrained acetabular liners, dual-mobility liners, and large heads (≥36 mm) are options for reducing subsequent dislocation. Standard head sizes have a higher rate of second revision for further dislocation. LEVEL OF EVIDENCE: Therapeutic Level III. See Instructions for Authors for a complete description of levels of evidence.
引用
- Hoskins W, Bingham R, Hatton A, et al. Standard, Large-Head, Dual-Mobility, or Constrained-Liner Revision Total Hip Arthroplasty for a Diagnosis of Dislocation: An Analysis of 1,275 Revision Total Hip Replacements. J Bone Joint Surg Am. 2020. PMID: 33264216. doi:10.2106/JBJS.20.00479
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。