旋转平台全膝关节置换术后的功能性屈曲不稳
该生物力学研究在6例新鲜冷冻尸体肢体上对旋转平台全膝关节置换(TKA-RP)假体进行测试,模拟5种屈伸间隙不匹配与不对称条件,并在0°、30°、60°加载。结果显示膝屈曲增加时设计性衬垫旋转减少、屈服扭矩增加,不对称屈曲间隙松弛可导致衬垫不稳与股骨髁抬升。
要点
- 膝屈曲角度增加时,设计性衬垫旋转减少而屈服扭矩增加。
- 关节松弛度增加时屈服扭矩降低。
- 外侧聚乙烯衬垫凹面深度决定股骨髁捕获,最小假体尺寸下屈曲间隙不对称容忍度<2 mm。
核心结论
- 随着膝屈曲增加,股骨-胫骨关节面一致性降低,加上不对称屈曲间隙松弛,使股骨假体在衬垫上表面而非下表面发生反常运动。
研究设计与样本
- 生物力学测试在6例新鲜冷冻尸体肢体上进行,采用间隙平衡技术植入TKA-RP假体,随后序贯更换不同厚度聚乙烯衬垫以系统模拟5种屈伸不匹配与不对称条件。
- 每种配置在0°、30°、60°进行机械加载,用数字卡尺测量衬垫在胫骨基板上的旋转位移、外侧间室分离和衬垫凹面深度,并用定制MATLAB代码计算屈服扭矩。
主要发现
- 每种加载配置下,设计性衬垫旋转随膝屈曲角度增加而减少。
- 所有测试配置中,屈服扭矩随关节屈曲增加而增加,随关节松弛度增加而降低。
- 在膝屈曲增加和不对称屈曲间隙松弛的位置可重现衬垫不稳与股骨髁位移。
- 外侧聚乙烯衬垫凹面深度决定股骨髁捕获,在最小假体尺寸下定义了<2 mm的屈曲间隙不对称窄容忍度,超过此值导致旋转性衬垫不稳。
关键数值与推荐
- 最小假体尺寸下,屈曲间隙不对称容忍度<2 mm,以防止旋转性衬垫不稳。
- 屈曲超过30°减少承重面接触面积,易致衬垫旋转减少和机械故障。
临床怎么用
- 作者指出,活动平台TKA-RP是技术要求高的手术,需要紧密对称的屈曲间隙。
- 作者指出,仅2 mm的外侧屈曲松弛不对称即可导致一致性降低、髁抬升和衬垫半脱位。
局限性
- 原文未报告局限性。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
BACKGROUND: We sought to define "at risk" loading conditions associated with rotating-platform total knee arthroplasty (TKA-RP) implants that predispose to insert subluxation and spinout and to quantify tolerances for flexion-extension gap asymmetry and laxity in order to prevent these adverse events. METHODS: Biomechanical testing was performed on 6 fresh-frozen cadaveric limbs with a TKA-RP implant with use of a gap-balancing technique, followed by sequential femoral component revision with variable-thickness polyethylene inserts to systematically represent 5 flexion-extension mismatch and asymmetry conditions. Each configuration was subjected to mechanical loading at 0°, 30°, and 60°. Rotational displacement of the insert on the tibial baseplate, lateral compartment separation, and insert concavity depth were measured with use of a digital caliper. Yield torque, a surrogate for ease of insert rotation and escape of the femoral component, was calculated with use of custom MATLAB code. RESULTS: Design-intended insert rotation decreased with increasing knee flexion angles in each loading configuration. Likewise, yield torque increased with increasing joint flexion and decreased with increasing joint laxity in all testing configurations. Insert instability and femoral condyle displacement were reproduced in positions of increasing knee flexion and asymmetrical flexion gap laxity. The depth of lateral polyethylene insert concavity determined femoral condylar capture and defined a narrow tolerance of <2 mm in the smallest implant sizes for flexion gap asymmetry leading to rotational insert instability. CONCLUSIONS: Decreased femoral-tibial articular surface conformity with increasing knee flexion and asymmetrical flexion gap laxity enable paradoxical motion of the femoral component on the upper insert surface rather than the undersurface, as designed. CLINICAL RELEVANCE: Mobile-bearing TKA-RP is a technically demanding procedure requiring a snug symmetrical flexion gap. As little as 2 mm of asymmetrical lateral flexion laxity can result in decreased conformity, condyle liftoff, and insert subluxation. Flexion beyond 30° decreases bearing surface contact area and predisposes to reduced insert rotation and mechanical malfunction.
引用
- Quinlan ND, Wu Y, Chiaramonti AM, et al. Functional Flexion Instability After Rotating-Platform Total Knee Arthroplasty. J Bone Joint Surg Am. 2020. PMID: 33027123. doi:10.2106/JBJS.19.01403
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。