文献速递关节外科

电灼导致全膝关节植入物损伤

Electrocautery Induced Damage of Total Knee Implants.
PubMed 文献 · J Arthroplasty · 2020-09-28

本研究通过问卷调查髋膝关节学会会员在植入假体后使用电灼的比例,并选取钴铬合金、Oxinium和氮化锆三种全膝关节置换 bearing 表面,用单极和双极电灼在3种能量设置下造成损伤,比较表面粗糙度参数与元素变化。结果显示双极损伤的Rz和Ra中位数大于单极,Oxinium表面粗糙度参数增加最大,调查显示相当比例成人重建外科医生在假体植入后使用电灼且未意识到这种损伤。

要点

  • 双极电灼损伤区域的Rz和Ra中位数大于单极,所有bearing表面均如此。
  • Oxinium表面的粗糙度参数增加最大。
  • 调查显示相当比例成人重建外科医生在假体植入后使用电灼,且未意识到这种损伤。

核心结论

  • 电灼造成的表面损伤可对植入物bearing表面产生显著影响,但需进一步研究以确定这是否为临床问题。
  • 调查发现许多关节置换专家不知道这种损伤可能发生。

研究设计与样本

  • 向髋膝关节学会会员发送问卷调查成人重建外科医生在组件植入后使用电灼的百分比。
  • 选取钴铬合金、Oxinium和氮化锆三种全膝关节置换bearing表面,用单极和双极电灼在3种不同能量设置下造成损伤。
  • 使用扫描电子显微镜比较表面损伤,使用能量色散光谱比较元素差异,并使用轮廓仪记录平均粗糙度(Ra)、最大峰谷高度(Rz)、峰度(Rk)和偏度(Rsk)进行比较。

主要发现

  • 所有bearing表面中,双极损伤区域的中位Rz和Ra测量值均大于单极。
  • Oxinium表面的粗糙度参数增加最大。
  • 背散射扫描电子显微镜分析发现双极损伤较单极有显著变化。
  • 调查结果显示相当比例的成人重建外科医生在植入物放置后使用电灼,且未意识到这种损伤。

局限性

  • 需要进一步研究以确定电灼造成的表面损伤是否为临床问题。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

BACKGROUND: Pitting damage on implants has been reported and attributed to the use of electrocautery. This study aimed to determine how different total knee arthroplasty bearing surfaces are susceptible to this type of damage and whether surgeons are aware that this damage can occur. METHODS: A survey was sent to Hip and Knee Society members to determine what percentage of adult reconstructive surgeons use electrocautery after implantation of components. Three bearing surfaces for total knee arthroplasty were selected: cobalt chromium, Oxinium, and zirconium nitride to be damaged by electrocautery with a monopolar (MP) and bipolar (BP) electrocautery with 3 different energy settings. A comparison of surface damage using scanning electron microscopy and elemental differences using energy dispersion spectroscopy was performed. Average roughness (Ra), maximal peak-to-valley height (Rz), kurtosis (Rk), and skewness (Rsk) were recorded for comparison using a profilometer was performed. RESULTS: Median Rz and Ra measurements were larger for BP damaged areas compared to MP for all bearing surfaces. The Oxinium surface had the greatest increase in roughness parameters. Survey results indicate that a significant percentage of adult reconstructive surgeons use the electrocautery after implants are in place and are not aware of this type of damage. Backscatter scanning electron microscopy analysis found significant changes for BP damage compared to MP. CONCLUSION: Surface damage caused by electrocautery can have significant effects on the bearing surfaces of implants but further study needs to be performed to determine if this is a clinical issue. Our survey determined that many arthroplasty experts are unaware that this damage can occur.

来源:J Arthroplasty,查看原文。版权归原作者所有。

引用

  1. Miller KC, Morrow BR, Sorrels JH, et al. Electrocautery Induced Damage of Total Knee Implants. J Arthroplasty. 2020. PMID: 33067092. doi:10.1016/j.arth.2020.09.044

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。