文献速递关节外科

不同程度骨丢失下髌骨假体固定的生物力学研究

Biomechanical Study of Patellar Component Fixation with Varying Degrees of Bone Loss.
PubMed 文献 · J Arthroplasty · 2020-08-25

该生物力学研究将60对尸体髌骨随机分入3组,模拟标准3孔TKA制备后,实验组分别将1、2、3个标准钻孔均匀扩大至12 mm以模拟骨丢失,骨水泥固定全聚乙烯髌骨假体后剪切测试。各组内对照与实验髌骨平均偏移屈服力差异均无统计学意义。结论认为在此生物力学尸体研究中,髌骨固定孔扩大至12 mm的骨丢失并未显著降低髌骨假体固定的剪切强度。

要点

  • 60对尸体髌骨随机分入3组,每组实验髌骨分别将1、2、3个标准钻孔扩大至12 mm模拟骨丢失。
  • 各组内对照与实验髌骨的平均偏移屈服力差异均无统计学意义。
  • 结论认为固定孔扩大至12 mm的骨丢失未显著降低髌骨假体固定的剪切强度。

核心结论

  • 在此生物力学尸体研究中,髌骨固定孔扩大至12 mm的骨丢失并未显著降低髌骨假体固定的剪切强度。

研究设计与样本

  • 研究为生物力学尸体研究,使用60对尸体髌骨随机分入3组,按标准3孔构型以类似全膝关节置换术(TKA)的方式制备。
  • 每对髌骨设对照髌骨与实验髌骨;实验髌骨分别将1、2、3个标准钻孔均匀扩大至12 mm以模拟骨丢失(对应第1组、第2组、第3组)。
  • 随后以骨水泥将全聚乙烯髌骨假体固定于每块髌骨,使用材料测试系统将髌骨假体剪切分离。
  • 采用配对t检验分析各组内平均偏移屈服力。

主要发现

  • 第1组对照髌骨的平均偏移屈服力大于实验髌骨。
  • 第2组和第3组实验髌骨的平均偏移屈服力大于对照髌骨。
  • 各组内对照与实验髌骨比较均未显示统计学显著差异。

临床怎么用

  • 原文未据此给出推荐。

局限性

  • 原文未报告局限性。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

BACKGROUND: The decision as to whether or not to resurface the patella in revision total knee arthroplasty (TKA) is affected by the amount of patellar bone stock remaining; however, the impact of the cancellous bone status on patellar component fixation has not been studied. Therefore, we conducted a biomechanical study of patellar component fixation with varying degrees of cancellous bone loss. METHODS: Sixty pairs of cadaveric patellae were randomly assigned between 3 groups and prepared in similar manner to a TKA with the standard 3-hole configuration. A control patella and an experimental patella were designated in each pair. To simulate bone loss in the experimental patellae, 1, 2, and 3 of the standard drill holes were uniformly enlarged to 12 mm in group 1, group 2, and group 3, respectively. Afterward, an all-polyethylene patellar component was cemented to each patella, as done intraoperatively. Patellar components were then sheared off using a materials testing system. The resulting mean offset yield force was analyzed within each group using paired t-tests. RESULTS: The mean offset yield force for the control patellae was greater than the experimental patellae in group 1. In groups 2 and 3, the experimental patellae produced a greater mean offset yield force than the control patellae. Comparison within each group did not demonstrate a statistically significant difference. CONCLUSION: Bone loss with enlargement of the patellar fixation holes, as is frequently seen in revision TKA, with holes up to 12 mm, does not significantly decrease patellar component fixation shear strength in this biomechanical cadaveric study.

来源:J Arthroplasty,查看原文。版权归原作者所有。

引用

  1. Beck CM, Nwannunu BI, Teigen KJ, et al. Biomechanical Study of Patellar Component Fixation with Varying Degrees of Bone Loss. J Arthroplasty. 2020. PMID: 32978021. doi:10.1016/j.arth.2020.08.044

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。