新型3D打印非骨水泥型与骨水泥型全膝关节置换术的迁移比较:基于放射立体分析随机对照试验的两年结果
研究将72例患者随机分配至非骨水泥3D打印或骨水泥型后交叉韧带保留型全膝关节置换术,用放射立体分析(RSA)随访两年。骨水泥组各时间点平均最大总点运动(MTPM)均低于非骨水泥组(p=0.003),但以3个月为基线后两组平均迁移无差异(p=0.497)。作者结论为非骨水泥假体前两年迁移更大,主要源于术后前3个月初始迁移较高,之后除一例力线不良并早期翻修者外均趋于稳定。
要点
- 骨水泥组3、12、24个月平均MTPM分别为0.33、0.42、0.47 mm,均低于非骨水泥组的0.52、0.62、0.64 mm(p=0.003)。
- 以3个月为基线,两组平均迁移无差异(p=0.497)。
- 骨水泥组3例在术后1至2年间MTPM增加超过0.2 mm;非骨水泥组1例因疼痛和进行性迁移翻修,1例因深部感染更换衬垫。
核心结论
- 非骨水泥型全膝关节置换术在术后前两年内的迁移大于骨水泥型。
- 该差异主要由于非骨水泥组术后前3个月初始迁移较高,之后除一例力线不良并早期翻修者外均观察到稳定。
- 非骨水泥假体的生物固定能否带来长期生存率提高,需要更长时间随访。
研究设计与样本
- 随机对照试验,共72例患者随机分配至非骨水泥3D打印组或骨水泥型后交叉韧带保留型全膝关节置换组。
- 在基线及术后3、12、24个月评估放射立体分析(RSA)和临床评分,采用混合模型分析重复测量。
主要发现
- 骨水泥组3、12、24个月平均最大总点运动(MTPM)分别为0.33 mm(95%CI 0.25至0.42)、0.42 mm(95%CI 0.33至0.51)、0.47 mm(95%CI 0.38至0.57)。
- 非骨水泥组3、12、24个月平均MTPM分别为0.52 mm(95%CI 0.43至0.63)、0.62 mm(95%CI 0.52至0.73)、0.64 mm(95%CI 0.53至0.75)(p=0.003)。
- 以3个月为基线,两组平均迁移无差异(p=0.497)。
- 骨水泥组3例假体在术后1至2年随访期间MTPM增加超过0.2 mm。
- 非骨水泥组1例因疼痛和进行性迁移翻修,1例因深部感染更换衬垫。
局限性
- 非骨水泥假体的生物固定能否带来长期生存率提高,需要更长时间随访。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
AIMS: Although bone cement is the primary mode of fixation in total knee arthroplasty (TKA), cementless fixation is gaining interest as it has the potential of achieving lasting biological fixation. By 3D printing an implant, highly porous structures can be manufactured, promoting osseointegration into the implant to prevent aseptic loosening. This study compares the migration of cementless, 3D-printed TKA to cemented TKA of a similar design up to two years of follow-up using radiostereometric analysis (RSA) known for its ability to predict aseptic loosening. METHODS: A total of 72 patients were randomized to either cementless 3D-printed or a cemented cruciate retaining TKA. RSA and clinical scores were evaluated at baseline and postoperatively at three, 12, and 24 months. A mixed model was used to analyze the repeated measurements. RESULTS: The mean maximum total point motion (MTPM) at three, 12, and 24 months was 0.33 mm (95% confidence interval (CI) 0.25 to 0.42), 0.42 mm (95% CI 0.33 to 0.51), and 0.47 mm (95% CI 0.38 to 0.57) respectively in the cemented group, versus 0.52 mm (95% CI 0.43 to 0.63), 0.62 mm (95% CI 0.52 to 0.73), and 0.64 mm (95% CI 0.53 to 0.75) in the cementless group (p = 0.003). However, using three months as baseline, no difference in mean migration between groups was found (p = 0.497). Three implants in the cemented group showed a > 0.2 mm increase in MTPM between one and two years of follow-up. In the cementless group, one implant was revised due to pain and progressive migration, and one patient had a liner-exchange due to a deep infection. CONCLUSION: The cementless TKA migrated more than the cemented TKA in the first two-year period. This difference was mainly due to a higher initial migration of the cementless TKA in the first three postoperative months after which stabilization was observed in all but one malaligned and early revised TKA. Whether the biological fixation of the cementless implants will result in an increased long-term survivorship requires a longer follow-up. Cite this article: Bone Joint J 2020;102-B(8):1016-1024.
引用
- Hasan S, van Hamersveld KT, Marang-van de Mheen PJ, et al. Migration of a novel 3D-printed cementless versus a cemented total knee arthroplasty: two-year results of a randomized controlled trial using radiostereometric analysis. Bone Joint J. 2020. PMID: 32731825. doi:10.1302/0301-620X.102B8.BJJ-2020-0054.R1
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。