高孔隙度钽髋臼假体不使用辅助螺钉在2年时的迁移与带螺钉的多孔钛髋臼假体相似:一项随机对照试验
该随机对照试验纳入66例40至64岁骨关节炎患者,术中随机接受无辅助螺钉固定的高孔隙度钽髋臼假体或带辅助螺钉固定的多孔钛髋臼假体。2年时钽组平均近端迁移0.17 mm(95%CI 0.09-0.24),不大于钛组的0.19 mm(95%CI 0.07-0.32),两组Harris髋关节评分和功能活动评分相似。
要点
- 2年时钽组平均近端迁移0.17 mm,钛组0.19 mm,钽组不大于钛组。
- 两组Harris髋关节评分和功能活动评分相似。
- 结果表明高孔隙度高摩擦涂层实心背衬模块化髋臼假体不使用辅助螺钉即可获得早期稳定。
核心结论
- 高孔隙度高摩擦涂层实心背衬模块化髋臼假体不使用辅助螺钉固定即可获得早期稳定。
研究设计与样本
- 随机对照试验,纳入66例40至64岁、骨关节炎且Charnley活动分级A或B级、接受初次全髋关节置换术的患者,术中随机分配接受钽或钛髋臼假体。
- 所有患者均接受同一骨水泥抛光锥形股骨柄、28 mm钴铬股骨头和高交联聚乙烯内衬。
- 使用放射立体分析在术后4-6天及术后6周、3个月、1年和2年测量髋臼假体迁移。
- 证据等级为Level I。
主要发现
- 2年时钽组平均近端迁移为0.17 mm(95%CI 0.09-0.24),钛组为0.19 mm(95%CI 0.07-0.32),钽组不大于钛组。
- 两组Harris髋关节评分和功能活动评分相似。
局限性
- 原文未报告局限性。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
BACKGROUND: It is proposed that highly porous coatings on acetabular components, such as a porous tantalum coating, provide adequate fixation without ancillary screw fixation in primary total hip arthroplasty (THA). However, tantalum acetabular components have been associated with higher rates of revision than other uncemented components in national registries. The aim of this randomized controlled trial is to determine whether the early migration of a solid-backed tantalum acetabular component was no greater than that of a titanium acetabular component with ancillary screw fixation that has proven good clinical results. METHODS: Sixty-six patients aged 40 to 64 years, with osteoarthritis and Charnley grade A or B activity grade and who underwent primary THA, were recruited into the trial. Patients were randomized intraoperatively to receive either the tantalum or titanium acetabular component. All patients received the same cemented polished tapered femoral stem, 28-mm cobalt-chromium femoral head, and highly cross-linked polyethylene liner. Acetabular component migration was measured using radiostereometric analysis at 4-6 days postoperatively and at 6 weeks, 3 months, 1 and 2 years following THA. RESULTS: The mean proximal migration at 2 years for the tantalum cohort was 0.17 mm (95% confidence interval, 0.09-0.24) which was no greater than that of the titanium cohort which was 0.19 mm (0.07-0.32). Harris hip scores and functional activity scores were similar between groups. CONCLUSION: These results demonstrate that early stability can be achieved without ancillary screw fixation through the use of a highly porous high friction coating on a solid-backed modular acetabular component. LEVEL OF EVIDENCE: Level I.
引用
- Howie DW, Holubowycz OT, Callary SA, et al. Highly Porous Tantalum Acetabular Components Without Ancillary Screws Have Similar Migration to Porous Titanium Acetabular Components With Screws at 2 Years: A Randomized Controlled Trial. J Arthroplasty. 2020. PMID: 32593487. doi:10.1016/j.arth.2020.05.049
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。