全髋关节置换术中外科医生装配技术对模块化锥度微力学影响的建模研究
本研究建立有限元模型,用临床医生采集的动态装配载荷模拟钴铬合金头与钛合金柄锥度界面的接触力学,并用五枚取回植入物的微槽变形特征验证模型。模型预测的微槽高度和宽度变化与取回植入物测量值无显著差异。模型发现低载荷(4 kN)下三次敲击较同载荷单次敲击降低锥度啮合、接触压力和微槽变形,提示低载荷多次敲击可能导致锥度锁定强度 inferior。
要点
- 有限元模型预测的微槽高度变化均值1.1 μm(0.2至1.3)与取回植入物测量值均值1.4 μm(0.4至2.3)无显著差异(p=0.109)。
- 模型预测的微槽宽度变化均值7.5 μm(1.0至18.5)与取回植入物测量值均值12.0 μm(1.5至25.4)无显著差异(p=0.470)。
- 低载荷(4 kN)下三次敲击较同载荷单次敲击降低整个柄锥度的啮合、接触压力和微槽变形。
核心结论
- 低载荷下额外敲击可能导致锥度锁定强度低于一次有力敲击,可能受加载速率或材料应变硬化影响。
- 该模型可估算代表取回植入物真实接触力学的微槽变形,有助于理解外科医生装配技术和植入物设计对锥度锁定强度的影响。
研究设计与样本
- 开发通用钴铬合金头与钛合金柄锥度的有限元模型,用临床医生采集的动态装配载荷驱动。
- 用五枚取回植入物的微槽高度和宽度变形特征验证模型接触力学。
- 用模型评估单次敲击与三次敲击装配技术对锥度互锁力学行为的作用。
主要发现
- 模型预测的微槽高度变化均值1.1 μm(0.2至1.3)在取回植入物测量高度变化均值1.4 μm(0.4至2.3)范围内(p=0.109)。
- 模型预测的微槽宽度变化均值7.5 μm(1.0至18.5)在取回植入物测量宽度变化均值12.0 μm(1.5至25.4)范围内(p=0.470)。
- 与台式研究一致,模型发现增加装配载荷幅度导致锥度啮合、接触压力和柄锥度微槽永久变形增加。
- 模型发现低载荷(4 kN)下三次敲击装配较同载荷单次敲击降低整个柄锥度的啮合、接触压力和微槽变形。
局限性
- 原文未报告局限性。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
AIMS: The aim of this study was to develop a novel computational model for estimating head/stem taper mechanics during different simulated assembly conditions. METHODS: Finite element models of generic cobalt-chromium (CoCr) heads on a titanium stem taper were developed and driven using dynamic assembly loads collected from clinicians. To verify contact mechanics at the taper interface, comparisons of deformed microgroove characteristics (height and width of microgrooves) were made between model estimates with those measured from five retrieved implants. Additionally, these models were used to assess the role of assembly technique-one-hit versus three-hits-on the taper interlock mechanical behaviour. RESULTS: The model compared well to deformed microgrooves from the retrieved implants, predicting changes in microgroove height (mean 1.1 μm (0.2 to 1.3)) and width (mean 7.5 μm (1.0 to 18.5)) within the range of measured changes in height (mean 1.4 μm (0.4 to 2.3); p = 0.109) and width (mean 12.0 μm (1.5 to 25.4); p = 0.470). Consistent with benchtop studies, our model found that increasing assembly load magnitude led to increased taper engagement, contact pressure, and permanent deformation of the stem taper microgrooves. Interestingly, our model found assemblies using three hits at low loads (4 kN) led to decreased taper engagement, contact pressures and microgroove deformations throughout the stem taper compared with tapers assembled with one hit at the same magnitude. CONCLUSION: These findings suggest additional assembly hits at low loads lead to inferior taper interlock strength compared with one firm hit, which may be influenced by loading rate or material strain hardening. These unique models can estimate microgroove deformations representative of real contact mechanics seen on retrievals, which will enable us to better understand how both surgeon assembly techniques and implant design affect taper interlock strength. Cite this article: Bone Joint J 2020;102-B(7 Supple B):33-40.
引用
- Gustafson JA, Pourzal R, Levine BR, et al. Modelling changes in modular taper micromechanics due to surgeon assembly technique in total hip arthroplasty. Bone Joint J. 2020. PMID: 32600210. doi:10.1302/0301-620X.102B7.BJJ-2019-1678.R1
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。