文献速递关节外科

新型承重面是否改变了对全髋关节置换术长期寿命的预期?

Have newer bearing surfaces changed expectations regarding the longevity of total hip arthroplasty?
PubMed 文献 · Bone Joint J · 2020-01-01

结果显示交联聚乙烯在15年随访中消除了磨损相关翻修,其翻修累积发生率低于传统聚乙烯;大直径股骨头降低了脱位翻修率;金属对金属承重面存在不良局部组织反应风险。

要点

  • 交联聚乙烯15年翻修累积发生率为4%,低于传统聚乙烯的18%和15%。
  • 金属对金属和表面置换组出现不良局部组织反应相关翻修。
  • 36mm及以上股骨头脱位翻修率为0.2%,低于小尺寸股骨头的2%。

核心结论

  • 与气相等离子灭菌传统聚乙烯和空气中γ射线灭菌传统聚乙烯相比,交联聚乙烯在15年随访中消除了磨损相关翻修。
  • 大直径股骨头的引入降低了脱位发生率,但脱位仍是持续存在的关注问题。
  • 金属对金属承重面的不良局部组织反应风险需要继续随访。

研究设计与样本

  • 单机构回顾性研究,纳入1982年至2010年间1707例初次全髋关节置换术,分为六种承重面队列。
  • 六组分别为:空气中γ射线灭菌传统聚乙烯223髋、气相等离子灭菌传统聚乙烯114髋、交联聚乙烯116髋、金属对金属1083髋、陶瓷对陶瓷90髋、表面置换81髋。
  • 除陶瓷对陶瓷组外,其余各组均使用钴铬股骨头。
  • 平均随访10年(范围0.008至35年)。

主要发现

  • 交联聚乙烯组15年翻修累积发生率为4%,低于空气中γ射线灭菌传统聚乙烯组的18%(p=0.02)。
  • 交联聚乙烯组15年翻修累积发生率为4%,低于气相等离子灭菌传统聚乙烯组的15%(p=0.003)。
  • 不良局部组织反应相关翻修仅见于金属对金属组(每100组件年0.8次翻修)和表面置换组(每100组件年0.1次翻修)。
  • 36mm及以上股骨头组的脱位翻修率为0.2%,低于小尺寸股骨头组的2%(p<0.001)。

关键数值与推荐

  • 交联聚乙烯组15年翻修累积发生率4% vs 空气中γ射线灭菌传统聚乙烯组18%(p=0.02)。
  • 交联聚乙烯组15年翻修累积发生率4% vs 气相等离子灭菌传统聚乙烯组15%(p=0.003)。
  • 金属对金属组不良局部组织反应翻修率0.8次/100组件年,表面置换组0.1次/100组件年。
  • 36mm及以上股骨头组脱位翻修率0.2% vs 小尺寸股骨头组2%(p<0.001)。

临床怎么用

  • 原文未据此给出推荐。

局限性

  • 原文未报告局限性。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

AIMS: The purpose of this study is to examine six types of bearing surfaces implanted at a single institution over three decades to determine whether the reasons for revision vary among the groups and how long it takes to identify differences in survival. METHODS: We considered six cohorts that included a total of 1,707 primary hips done between 1982 and 2010. These included 223 conventional polyethylene sterilized with γ irradiation in air (CPE-GA), 114 conventional polyethylene sterilized with gas plasma (CPE-GP), 116 crosslinked polyethylene (XLPE), 1,083 metal-on-metal (MOM), 90 ceramic-on-ceramic (COC), and 81 surface arthroplasties (SAs). With the exception of the COC, all other groups used cobalt-chromium (CoCr) femoral heads. The mean follow-up was 10 (0.008 to 35) years. Descriptive statistics with revisions per 100 component years (re/100 yr) and survival analysis with revision for any reason as the endpoint were used to compare bearing surfaces. RESULTS: XLPE liners demonstrated a lower cumulative incidence of revision at 15 years compared to the CPE-GA and CPE-GP groups owing to the absence of wear-related revisions (4% for XLPE vs 18%, p = 0.02, and 15%, p = 0.003, respectively). Revisions for adverse local tissue reactions occurred exclusively among the MOM (0.8 re/100 year) and SA groups (0.1 re/100 year). The revision rate for instability was lower among hips with 36 mm and larger head sizes compared to smaller head sizes (0.2% vs 2%, p < 0.001). CONCLUSION: The introduction of XLPE has eliminated wear-related revisions through 15-year follow-up compared to CPE-GP and CPE-GA. Dislocation incidence has been reduced with the introduction of larger diameter heads but remains a persistent concern. The potential for adverse local tissue reactions with MOM requires continued follow-up. Cite this article: Bone Joint J 2020;102-B(7 Supple B):105-111.

来源:Bone Joint J,查看原文。版权归原作者所有。

引用

  1. Engh CA, McAsey CJ, Cororaton AD, et al. Have newer bearing surfaces changed expectations regarding the longevity of total hip arthroplasty? Bone Joint J. 2020. PMID: 32600211. doi:10.1302/0301-620X.102B7.BJJ-2019-1545.R1

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。