模块化双动髋关节假体的体内腐蚀:取回研究
研究对12例平均体内留存26个月(范围1-57个月)的模块化双动全髋关节置换假体进行取回分析,采用改良Goldberg标准定性分级并用坐标测量机定量测量,发现所有假体内衬锥度区均存在不同程度的钴铬金属腐蚀/磨损,平均最大线性腐蚀深度35.5微米(范围8.4-176.2微米),作者建议在更大样本临床相关性研究完成前应审慎使用此类假体。
要点
- 12例取回模块化双动假体平均体内留存26个月,全部存在可识别的内衬锥度区腐蚀/磨损。
- 2例(17%)为重度4级腐蚀,5例(42%)为中度3级,4例(33%)为轻度2级,1例(8%)为1级(无可见腐蚀)。
- 平均最大线性腐蚀深度35.5微米,所有假体均超过7微米这一提示潜在临床显著材料损失的阈值。
核心结论
- 对全部12例取回模块化双动假体的视觉与尺寸分析显示,钴铬金属内衬锥度区存在可识别的、严重程度不一的腐蚀/磨损。
- 作者认为在完成更大样本并具备临床相关性的研究之前,应审慎使用这些假体。
研究设计与样本
- 取回研究,评估12例同一设计的模块化双动全髋关节置换假体,平均体内留存26个月(范围1-57个月)。
- 6例(50%)来自初次全髋关节置换,6例(50%)来自翻修全髋关节置换。
- 对存在损伤风险的内衬锥度区采用改良Goldberg标准进行定性分级,并使用经验证的坐标测量机进行定量尺寸评估。
主要发现
- 取回假体中2例(17%)为重度4级腐蚀,5例(42%)为中度3级腐蚀,4例(33%)为轻度2级腐蚀,1例(8%)为1级(无可见腐蚀)。
- 锥度界面平均最大线性腐蚀深度为35.5微米(范围8.4-176.2微米)。
- 所有假体最大线性腐蚀深度均>7微米,该阈值提示可能存在临床显著的材料损失。
- 识别出三种腐蚀模式:弥漫性腐蚀、锥度区中部条带状腐蚀、以及最靠近关节面的锥度部分局灶性腐蚀。
关键数值与推荐
- 改良Goldberg腐蚀分级:1级无可见腐蚀,2级轻度,3级中度,4级重度。
- 最大线性腐蚀深度>7微米被视为提示潜在临床显著材料损失的阈值。
临床怎么用
- 作者认为这些假体应审慎使用,直至完成更大样本并具备临床相关性的研究。
局限性
- 原文未报告局限性。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
BACKGROUND: Modular dual-mobility (MDM) total hip arthroplasty (THA) implants have an additional metal-metal interface between the metal liner and outer metal shell that poses a risk of corrosion. The purpose of this study is to evaluate retrieved MDM liners to evaluate qualitative and quantitative damage and corrosion patterns at this interface. METHODS: Twelve MDM implants of one design with a mean in situ duration of 26 months (range, 1-57 months) were evaluated. Six implants (50%) were from primary THAs and 6 (50%) from revision THAs. The taper region of the liner at risk of damage was qualitatively graded using modified Goldberg criteria while quantitative dimensional assessment was performed with a validated coordinate measurement machine. RESULTS: Among the retrieved implants, 2 (17%) demonstrated severe grade 4 corrosion, 5 (42%) moderate grade 3 corrosion, 4 (33%) mild grade 2 corrosion, and 1 (8%) grade 1 (no visible corrosion). Mean maximum linear corrosion depth at the taper interface measured 35.5 microns (range, 8.4-176.2 microns). All implants had a maximum linear corrosion depth >7 microns, a threshold suggestive of potentially clinically significant material loss. Three corrosion patterns were identified: generalized corrosion, a stripe of corrosion about the middle of the taper region, and focal areas of corrosion at the portion of the taper closest to the joint surface. CONCLUSION: Visual and dimensional analysis of all 12 retrieved MDM implants demonstrated identifiable corrosion/wear of the cobalt-chromium metal liner taper of varying severity. These implants should be used judiciously until larger series with clinical correlation can be completed.
引用
- Kolz JM, Wyles CC, Van Citters DW, et al. In Vivo Corrosion of Modular Dual-Mobility Implants: A Retrieval Study. J Arthroplasty. 2020. PMID: 32600814. doi:10.1016/j.arth.2020.05.075
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。