步态依赖模型可预测回收全膝关节置换假体磨损
该回顾性纵向研究将11例回收聚乙烯胫骨垫与患者步态分析匹配,用Archard磨损方程从个体步态力学预测体积磨损并与实测比较。8例未分层组件实测总磨损率15.9 mm³/年,模型预测16.4 mm³/年;总部件和内侧实测与预测磨损体积显著相关(p=0.017和p=0.012),外侧不显著(p=0.154)。结论认为无分层时患者步态力学直接影响胫骨组件磨损。
要点
- 个体步态力学驱动的模型可预测未分层聚乙烯垫的总和内侧磨损。
- 实测与预测磨损在总部件(p=0.017)和内侧(p=0.012)显著相关。
- 外侧磨损实测与预测无显著相关(p=0.154)。
核心结论
- 无分层情况下,患者步态中个体化膝关节力学直接影响全膝关节置换胫骨组件磨损。
研究设计与样本
- 回顾性纵向研究,将11例回收聚乙烯胫骨垫与这些患者的步态分析测试匹配。
- 用激光坐标测量机和自主重建测量关节面体积磨损。
- 以个体步态试验的膝关节运动学和动力学驱动计算模型,计算内外侧胫股接触路径和力。
主要发现
- 8例未分层组件实测总磨损率为15.9 mm³/年(SE ± 7.7),内侧11.4 mm³/年(SE ± 6.4),外侧4.4 mm³/年(SE ± 2.6)。
- 步态力学模型预测总磨损率16.4 mm³/年(SE 2.4),内侧11.7 mm³/年(SE 2.1),外侧4.7 mm³/年(SE 0.4)。
- 实测与预测磨损体积在总部件(p = 0.017)和内侧(p = 0.012)显著相关,外侧不显著(p = 0.154)。
关键数值与推荐
- 以Archard磨损方程,用接触路径滑动距离、法向力和植入时间预测体积磨损。
- 实测与预测磨损体积在总部件和内侧显著相关(p = 0.017和p = 0.012),外侧不显著(p = 0.154)。
临床怎么用
- 提示患者个体步态力学是胫骨组件磨损的重要影响因素,可用于磨损预测建模。
- 该模型对内侧磨损预测较好,外侧预测能力有限,临床应用需谨慎解读。
局限性
- 样本量小,仅11例回收聚乙烯垫,其中8例未分层组件用于磨损率分析。
- 外侧实测与预测磨损无显著相关,模型对外侧磨损预测能力有限。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
AIMS: A retrospective longitudinal study was conducted to compare directly volumetric wear of retrieved polyethylene inserts to predicted volumetric wear modelled from individual gait mechanics of total knee arthroplasty (TKA) patients. METHODS: In total, 11 retrieved polyethylene tibial inserts were matched with gait analysis testing performed on those patients. Volumetric wear on the articular surfaces was measured using a laser coordinate measure machine and autonomous reconstruction. Knee kinematics and kinetics from individual gait trials drove computational models to calculate medial and lateral tibiofemoral contact paths and forces. Sliding distance along the contact path, normal forces and implantation time were used as inputs to Archard's equation of wear to predict volumetric wear from gait mechanics. Measured and modelled wear were compared for each component. RESULTS: Volumetric wear rates on eight non-delaminated components measured 15.9 mm3/year (standard error (SE) ± 7.7) on the total part, 11.4 mm3/year (SE ± 6.4) on the medial side and 4.4 (SE ± 2.6) mm3/year on the lateral side. Volumetric wear rates modelled from patient gait mechanics predicted 16.4 mm3/year (SE 2.4) on the total part, 11.7 mm3/year (SE 2.1) on the medial side and 4.7 mm3/year (SE 0.4) on the lateral side. Measured and modelled wear volumes correlated significantly on the total part (p = 0.017) and the medial side (p = 0.012) but not on the lateral side (p = 0.154). CONCLUSION: In the absence of delamination, patient-specific knee mechanics during gait directly affect wear of the tibial component in TKA. Cite this article: Bone Joint J 2020;102-B(6 Supple A):129-137.
引用
- Knowlton CB, Lundberg HJ, Wimmer MA, et al. Can a gait-dependent model predict wear on retrieved total knee arthroplasty components? Bone Joint J. 2020. PMID: 32475284. doi:10.1302/0301-620X.102B6.BJJ-2019-1635.R1
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。