文献速递关节外科

113例非骨水泥模块化翻修股骨部件的机械失效

Mechanical failure of 113 uncemented modular revision femoral components.
PubMed 文献 · Bone Joint J · 2020-01-01

该研究基于113例非骨水泥模块化翻修股骨部件断裂病例,计算断裂率为0.30%(113/37,600),无不当使用迹象者断裂率为0.11%(41/37,600)。逻辑回归分析显示男性、高BMI、直型部件设计和小号颈段是失效的显著风险因素,79%(89/113)的失效病例使用了外侧化颈段或超长头。结论认为模块化连接处失效与患者和植入物特异性风险因素及植入技术错误相关,应避免使用短和外侧化颈段。

要点

  • 非骨水泥模块化翻修股骨部件断裂率为0.30%(113/37,600),无不当使用迹象者为0.11%(41/37,600)。
  • 男性、高BMI、直型部件设计和小号颈段是植入物失效的显著风险因素。
  • 79%(89/113)的失效病例使用了外侧化颈段、超长头或两者组合,应尽量避免。

核心结论

  • 模块化连接处植入物失效与患者和植入物特异性风险因素以及植入过程中的技术错误相关。
  • 应尽可能避免在该翻修系统中使用短和外侧化颈段,并遵守植入说明和禁忌症。

研究设计与样本

  • 研究评估了一个大型数据库中单一非骨水泥模块化翻修股骨部件机械失效为终点的病例,并与使用相同植入物的对照组比较。
  • 截至2017年4月,识别所有来自同一制造商的断裂非骨水泥模块化翻修股骨部件病例,使用截至2017年4月销售的总植入物数量计算断裂率。
  • 制造商提供了所有已通知断裂装置的患者人口学、失效时间和植入物详细信息。
  • 使用多重插补的逻辑回归模型评估患者和植入物特异性风险因素,并与先前发表的未观察到断裂的参考组数据比较。
  • 制造商对断裂植入物进行的回收分析结果可供评估。

主要发现

  • 记录了113例模块化连接处断裂,计算断裂率为0.30%(113/37,600)。
  • 无不当使用迹象的植入物断裂率为0.11%(41/37,600)。
  • 79%(89/113)的失效植入物病例使用了外侧化(高偏移)颈段、超长头或两者组合。
  • 逻辑回归分析显示男性、高体重指数(BMI)、直型部件设计和小号颈段是失效的显著风险因素。
  • 对76/113例植入物的调查显示,72例至少有一个不当使用迹象。

关键数值与推荐

  • 断裂率:0.30%(113/37,600);无不当使用迹象者断裂率:0.11%(41/37,600)。
  • 失效病例中79%(89/113)使用了外侧化颈段、超长头或两者组合。
  • 逻辑回归分析中男性、高BMI、直型部件设计和小号颈段为显著风险因素。
  • 回收分析中76例受检植入物有72例显示至少一个不当使用迹象。

临床怎么用

  • 在该翻修系统中应尽可能避免使用短和外侧化颈段。
  • 植入时应遵守植入说明和禁忌症,注意避免技术错误。
  • 对于男性、高BMI患者使用直型部件设计或小号颈段时需警惕失效风险。

局限性

  • 原文未报告局限性内容。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

AIMS: We evaluated a large database with mechanical failure of a single uncemented modular femoral component, used in revision hip arthroplasty, as the end point and compared them to a control group treated with the same implant. Patient- and implant-specific risk factors for implant failure were analyzed. METHODS: All cases of a fractured uncemented modular revision femoral component from one manufacturer until April 2017 were identified and the total number of implants sold until April 2017 was used to calculate the fracture rate. The manufacturer provided data on patient demographics, time to failure, and implant details for all notified fractured devices. Patient- and implant-specific risk factors were evaluated using a logistic regression model with multiple imputations and compared to data from a previously published reference group, where no fractures had been observed. The results of a retrieval analysis of the fractured implants, performed by the manufacturer, were available for evaluation. RESULTS: There were 113 recorded cases with fracture at the modular junction, resulting in a calculated fracture rate of 0.30% (113/37,600). The fracture rate of the implant without signs of improper use was 0.11% (41/37,600). In 79% (89/113) of cases with a failed implant, either a lateralized (high offset) neck segment, an extralong head, or the combination of both were used. Logistic regression analysis revealed male sex, high body mass index (BMI), straight component design, and small neck segments were significant risk factors for failure. Investigation of the implants (76/113) showed at least one sign of improper use in 72 cases. CONCLUSION: Implant failure at the modular junction is associated with patient- and implant-specific risk factors as well as technical errors during implantation. Whenever possible, the use of short and lateralized neck segments should be avoided with this revision system. Implantation instructions and contraindications need to be adhered to and respected. Cite this article: Bone Joint J 2020;102-B(5):573-579.

来源:Bone Joint J,查看原文。版权归原作者所有。

引用

  1. Krueger DR, Guenther KP, Deml MC, et al. Mechanical failure of 113 uncemented modular revision femoral components. Bone Joint J. 2020. PMID: 32349597. doi:10.1302/0301-620X.102B5.BJJ-2019-1333.R2

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。