文献速递关节外科

杜克大学医学中心新冠疫情期间3D打印改装骨科头盔作为个人防护装备的新技术

Helmet Modification to PPE With 3D Printing During the COVID-19 Pandemic at Duke University Medical Center: A Novel Technique.
PubMed 文献 · J Arthroplasty · 2020-04-18

新冠疫情期间医护人员需佩戴N95口罩或同等防护及面罩进行产生气溶胶的操作,但美国面临个人防护装备短缺,使用放大镜和头灯的外科医生难以同时使用面罩。多数关节置换外科医生使用手术头盔系统,但疫情期间择期关节置换手术推迟导致头盔闲置。作者因此开始将这些关节置换头盔改装为个人防护装备,本文概述了其构想、设计、穿戴技术和安全测试。

要点

  • 关节置换手术头盔系统可改装为个人防护装备以应对短缺
  • 使用放大镜和头灯的外科医生难以同时使用面罩
  • 本文概述了改装头盔的构想、设计、穿戴技术和安全测试

核心结论

  • 关节置换头盔系统可被改装为个人防护装备,以应对新冠疫情期间个人防护装备短缺的问题。

研究设计与样本

  • 本文为技术描述性文章,概述了将关节置换头盔改装为个人防护装备的构想、设计、穿戴技术和安全测试。

主要发现

  • 美国面临个人防护装备短缺,使用放大镜和头灯的外科医生难以同时使用面罩。
  • 多数关节置换外科医生使用的手术头盔系统在择期手术推迟期间闲置,作者已开始将其改装为个人防护装备。

临床怎么用

  • 在个人防护装备短缺时,可考虑将闲置的关节置换头盔系统改装为个人防护装备供医护人员使用。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

Care for patients during COVID-19 poses challenges that require the protection of staff with recommendations that health care workers wear at minimum, an N95 mask or equivalent while performing an aerosol-generating procedure with a face shield. The United States faces shortages of personal protective equipment (PPE), and surgeons who use loupes and headlights have difficulty using these in conjunction with face shields. Most arthroplasty surgeons use surgical helmet systems, but in the current pandemic, many hospitals have delayed elective arthroplasty surgeries and the helmet systems are going unused. As a result, the authors have begun retrofitting these arthroplasty helmets to serve as PPE. The purpose of this article is to outline the conception, design, donning technique, and safety testing of these arthroplasty helmets being repurposed as PPE.

来源:J Arthroplasty,查看原文。版权归原作者所有。

引用

  1. Erickson MM, Richardson ES, Hernandez NM, et al. Helmet Modification to PPE With 3D Printing During the COVID-19 Pandemic at Duke University Medical Center: A Novel Technique. J Arthroplasty. 2020. PMID: 32354536. doi:10.1016/j.arth.2020.04.035

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。